What is the most common control cable used (size)?

Q: Critical damping of the system ?

A: Given: Mass,m=13.8 kgSpring stiffness,k =1365 N/mDamping coefficient=17 Ns/mCritical damping of the…

Q: WHAT IS THE TOTAL SIZE CHANGE OF THE AC BAR

A:

Q: critical damping of the system ?

A: Given: A vibratory system consists of a mass,m=13.5 kgSpring stiffness,k=1355 N/mdamping…

Q: Critically explain the Joint servomechanism (PUMA robot arm control scheme)

A: Servomechanism A servomechanism or a servo is an automated device that senses changes and uses a…

Q: Examine the circuit shown and answer the following questions: 1. Describe 5 key features (ways,…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Statics; working

A:

Q: wo components are to be connected by bolts. One of components is relativel nnection is disassembled…

A: Stage 1: One of the segment is relatively thick.  It is cleared from outlines that initial two sorts…

Q: Define the following, Joint. Link. Joint space. Actuator space.

A: Joint: A point where two or more than two links are connected is known as joint. Link: It is a…

Q: the open circuit voltage and

A: Given; In a DC are welding operation, the voltage-arc length characteristics was obtained as,…

Q: Members that are joined together to form a kinematic chain Link Bar Pin Joint

A: As per company's guidelines we can answer only first question.

Q: What is the most common size of a control cable?

A: Control cables are the flexible steel cables used in the aircraft control systems.  The most common…

Q: How many wires are normally connected to adouble-filament light bulb?

A: In double filament light bulbs, two filaments, which are independent to each other are used. Double…

Q: Explain the installation procedures of a flexible coupling

A: given; explain the installation procedures of a flexible coupling.

Q: Why is high voltage needed to establish a spark across the gap of a spark plug

A: The air-fuel mixture is ignited inside the combustion chamber with the help of spark generated by…

Q: 16. When a pneumatic solenoid fails, the failure is normally due to a O A. weak pilot. O B. bad…

A: When seal is damaged, the valve does not shut off properly. after a close inspection damaged…

Q: What is the difference between Momentary Contact and Maintained Contact?

A: Maintained Contact means that when you push it on it stays on until you push it off and so on.

Q: What are the two types of wires and which is the mostcommonly used in automobiles?

A: There are mainly two types of wires are mainly Used in  the industrial applications. The first is…

Q: the following shadec

A: given:

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

A:

Q: ility and static determina

A: given:

Q: What are Ball and socket connections

A: The ball and socket connection  also known as spheroid joint, is a type of joint in which the…

Q: What do you mean by factor of safety and explain with an example.

A: Factor of safety: It is the ratio of the ultimate strength to the actual working stress of any…

Q: Q4: Two components are to be connected by bolts. One of components is relatively thick and the…

A: Given:

Q: What is the purpose of the control cable.

A: Control cables are multi-conductor cables used for automation and instrumentation applications.…

Q: voltage.

A: answer - 267.69V

Q: what could be the fault if a module does not respond to the diagnostic scan tool

A: Modern vehicles have many modules to control different vehicle systems. If there is a communication…

Q: Why wires are covered by rubber or plastic covering?

A: wires are covered by rubber or plastic due to prevent of electric shocks.

Q: What is normal operating conditions?

A: Normal operating condition refers to the condition at which any machine can work without any fatigue…

Q: From the following identify the true statement. O In electrical safety precaution, all non-metallic…

A: out of the 4 statements

Q: 9. Some of the motor is driven by inverter. Draw a Inverter control circuit for Mechanical brake…

A: Motors with various types of inverter drives are available with setup parameters to control the…

Q: Hinged at both ends. Find : (2. TcD = ?. (3) O LT=?

A:

Q: Which may not be an input of a control system? * actuating signal; setpoint; controlled variable;…

A:

Q: failure Mode why bellows corrosion.cause of corosion bellows and their solutions

A: Given Bellow To find Cause of corrosion Solution to corrosion

Q: Entire frame, pulleys, and contacting cable to be isolated as a single unit. B

A: TO draw the FBD of the given system we have to consider the weight and forces applied to the system.…

Q: What is low tension system and magneto mechanical system?

A: Solution:

Q: The Electric hand dryer is an example of........ loop system

A:

Q: How to manufacture a motor for electric vehicle ? Manufacturing method, Material, Shape and Size,…

A: A stator and a rotor are the two major components of a three-phase, four-pole induction motor. A…

Q: Less staff is required for breakdown maintenance which is carried out as fast as possible to bring a…

A: Let us discuss breakdown maintenance.

Q: Orthographic view of the component using creo software

A:

Q: What is the lowest acceptable amperage setting for GTAwelding?

A: Gas tungsten arc welding (GTAW), also known as tungsten inert gas (TIG) welding, is an arc welding…

Q: In a DCV, this part is located on either or both sides of the spool to position it in the middle…

A: DCV is the directional control value that performs 3 functions, 1. Allow the fluid flow, 2. Change…

Q: Mobility of a mechanism represents the number of required to run the mechanism. OLinks All of these…

A: Mobility is the number of inputs required to define the motion of mechanism.

Q: preload on screws for reused connections is lower than permanent connections Select one: O True O…

A: preload on screws for reused connections ,non-permanent connections is 75 percent of proof load.…

Q: What are the types of joint in the robotic system?

A: Given data What are the types of joint in the robotic system.

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.