Which may not be an input of a control system? * actuating signal; setpoint; controlled variable; reference value.

Q: The final control element in a closed loop control system is known as correction element measurement…

A: The final control  element of control loop system is known as Measurement Element.

Q: With a neat block Diagram explain the Functional block of CRO?

A:

Q: How system reliability is difference from individual component reliability

A:

Q: throttle actuator velocity v intake pipe throttle angle (aTH) slope (a) For vehicle speed control…

A: given; ⇒moving velocity =v⇒car moving with acceleration =a  ⇒lets take weight of body =w⇒normal…

Q: Work of a spring force (with final position in compressed state, initial position in undeformed…

A:

Q: (PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare…

A: Feedback Solution (1): This feedback control starts with a level transmitter that will measure the…

Q: Which of the following is correct for a open loop system ?

A: The main problem with the open loop control system is that, it do not monitor or check the condition…

Q: 1.Understand the given Physical process control diagram and explain the working of the system.…

A: BRIEF :- It is basically a machine primarily designed to monitor the fluid volume in the tanks. The…

Q: ») Explain the basic components of closed loop system shown in figure (a) Error Detector Actuating…

A: A closed-loop control system can be defined as, a system that has a feedback loop (or) a control…

Q: Suppose a process has been monitored daily for the last ten days and the number of machine failures…

A: A c-chart is a characteristics control chart for data collected in equal-sized subsets. C-charts…

Q: 4. The analyst in the Red Diamond Electronics Company wishes to assign a number of like facilities…

A: Given data: l=0.34+0.26=0.6 minutesm=1.48 minutesC1=$12 per hourC2=$18 per hourw=0.06 Need to…

Q: What is the sequence to do to simulate a control system with simulink?

A: What is the sequence to do to simulate a control system with simulink?

Q: Represent in block diagram form, the control system used in automatic control of speed of a steam…

A:

Q: xplain the role of feed back signal and error signal in a closed-loop control system

A: Role of Feedback system:- Feedback is taken into account to be a significant part of a closed-loop…

Q: What is the control plane's principal function?

A: Introduction: In a network there are various planes have different works. Every plane or part of…

Q: is an interconnection of components forming a system configuration that will provide a desired…

A:

Q: 6 - Which of the following statements about simultaneous control is incorrect? A) The most…

A: the incorrect simultaneous control is   The most well-known form of simultaneous control is indirect…

Q: In the mid-1900s, several technological and analysis concepts came together to make the PID…

A: A PID controller regulates temperature, flow, pressure, speed, and other process variables in…

Q: Warning- If not anything upto the mark, I'll report and dislike you. Define availability. For open…

A: Given data     a) Define availability!     b) formulate useful work and maximum useful work…

Q: Process control is generally referred as А. Process to enhance quality and quantity of final output…

A:

Q: capacity is the maximum output rate that can be achieved by a facility under ideal conditions.…

A:

Q: Task: 1. Discuss the fundamental concept and analyse the operation of Automatic Flight Control…

A: Given Aircraft Flight Control System To find  Concept  Operation

Q: Identify the system which is unreliable. a.

A: In manufacturing Engineering Machine input and output is controlled by 2 systems  by close loop or…

Q: CTD and BOM are one-to-one related to each other regarding the abstraction levels: False True

A: Solution:   CTD stands for Common Technical Document. BOM stands for Bill of materials.

Q: explain Interactive Single Variable process control loop for cooling tower with suitable…

A: A cooling tower is a heat-removal device that employs water to release waste heat from a process…

Q: Q1) Consider the steering control of an automobile. The objective is to control the direction of the…

A: The block diagram of a steering control system is shown below.

Q: control system is the automation of machine tools that are operated by a programmed command. O a.…

A: Numerical control  is the automatic control of machine tools by means of a computer.A CNC machine…

Q: i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction Element

A: Given: To identify: (i) Process Element (ii) Feedback Element (iii) Control Element (iv) Correction…

Q: (Can someone help me with this just need a P&ID solution meeting the requirements and explanation.…

A: A P&ID gives a point by point graphical portrayal of the genuine interaction framework that…

Q: 10- From the below following, identify the part of the output signal, which is sent back to the…

A: In an open-loop control system, the controlling action is independent of the system output which is…

Q: PID controller is also known as a

A: PID controller is also known as a _Three term Controller__ .

Q: Which type of control system is used in the given block diagram? Write the definition.

A: The Control system used in this diagram is open-loop control system.

Q: What is a control system? * A technical or physical device, process or system, in which cause-effect…

A: Given Data⇒ Control system

Q: 3. () Describe the type of attitude control components you would use for your spacecraft. How would…

A: Controlling the alignment of a satellite's axis while it orbits in space is referred to as…

Q: Represent in block diagram form, the control system used in automatic control of speed of a steam…

A: There are following operation of governing system-1.Limits the maximum speed of the generator.…

Q: What is an interrupt? define and explain how Transfer of Control via Interrupts?

A:

Q: Identify the control system areas of the BMS.

A: Given question: Identify the control system areas of the BMS

Q: What is a overdamped system?

A: A system is called over damped, if the damping ratio is greater than one, here system shows…

Q: b. Identify a real life device/control system configured as Closed-loop Control system and provide…

A: Solution:  A) Open Loop Control system:  A control system in which the control action is…

Q: What does SAP Supply Chain Coordination entail?

A: SAP supply chain management application enables the customer-centric business process automatic…

Q: Explain the robot hand grasping force control system in detail with block diagram and justify it as…

A: Robot hand grasping force : So when a robot hand want to grasp an object it requires an certain…

Q: system can control machines in the real time by executing instruction blocks 15. .. ..... * one by…

A: Direct numerical control (DNC), also known as distributed numerical control (also DNC), is a common…

Q: The role of control element in the closed loop system is

A: Answer:

Q: Draw the circuit diagram for the following system. The diagram must be neat, legible, and…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Operation of the Open Loop systems are based on the Feedback action. Select one: True OFalse

A: It is required to evaluate given statement

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.