What is the the volume flow rate (m³/s) and the mass flow rate (kg/s) at the inlet at the duct exit if the refrigerant-134a is used in a heating system? The refrigerant enters a cylindrical duct with a 50-cm diameter steadily at 2.4 bar and 298.15K with a velocity of 8 m/s. The refrigerant gains heat as it flows and leaves the duct at 2 bar and 313.15K.

What is the the volume flow rate (m³/s) and the mass flow rate (kg/s) at the inlet at the duct exit if the refrigerant-134a is used in a heating system? The refrigerant enters a cylindrical duct with a 50-cm diameter steadily at 2.4 bar and 298.15K with a velocity of 8 m/s. The refrigerant gains heat as it flows and leaves the duct at 2 bar and 313.15K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steams are 4 MPa, 500 C and 93m/s, and the exit conditions are 30 kPa, 89 percent quality, and 38m/s. the mass flow of the steam is 28kg/s. Determine:a) the change in kenitic energy b) the power outputc) turbine inlet area
Air flows into a turbine at a rate 30 [m 3 /s], a temperature of 1100 [K] anda pressure of 300 [kPa]. The turbine’s work output is 200 [kJ/kg]. Determine thetemperature of the air at the exit, the power output in [kW] and the isentropicefficiency. The pressure ratio of the turbine is 3. The specific gas constant, R, for airis 0.287 [kJ/kg-K].
Prove this equation for the frictional adiabatic process in a fixed cross-section duct.(Dont handwriten)
Refrigerant-134a enters a compressor at 200 kPa as a saturated vapor with a flowrate of 0.45 m3/min and leaves at 800 kPa. The power supplied to the refrigerant duringcompression process is 3 kW. What is the enthalpy of R-134a at the exit of the compressor?(Answer: 284.5 kJ/kg)
In Otto Cycle, air at 18oC is first compressed to one-ninth of its original volume. If the heat input to the cycle is 460 KJ/Kg of air, determine a. The temperature of the remaining points in the cycle. b. The ratio of the maximum and minimum pressure in the cycle.
5 kg/sec of steam enters the condenser at 0.10 mpa and 88% quality. The cooling water enters @ 33C and leaves at 39C. Determine the volume flow of the cooling water in the liters per minute at the inlet
An air compressor has a suction volume of 0.35 cubic meter/sec at 28 deg. C and 101.325 Kpa and discharges 700 kpa. Determine the amount of power saved by the compressor in two staging?
A steady-flow, steady-state thermodynamic system receives 1.67 lb/sof a fluid at 4320 psfa and 200°F and discharges it from a point80-ft above the entrance section at 21600 psfa and 600°F. The fluidenters with velocity of 120 ft/s and leaves with a velocity of 40ft/s. During this process, there are supplied 400 Btu/min of heatfrom an external source, and the increase in enthalpy is 2.0 Btu/lb.Determine the work done in horsepower.
Refrigerant R-134a at 400 kPa and T1=10⁰C enters an adiabatic diffuser steadily with a velocity of 600 m/s and leaves at 600 kPa andT2= 100⁰C. Determine:a) The exit velocityb) The inlet to exit area ratioc) The inlet exit density ratio
An adiabatic piston-cylinder device equipped with aspring maintains the pressure inside at 300 kPa, when thevolume is 0, and in 3 000 kPa, when the volume is 5 m ^ 3. Thedevice connects to a steam supply lineat 1,500 kPa and 200 ° C, and at the beginning the volume of the cylinder is 0.Determine the final temperature (and quality, if applicable) whenthe valve is opened and water vapor is allowed to enter from thesupply to the cylinder, until the pressure inside is equal tothe one on the line. Also determine the total workperformed during this adiabatic filling process.
he refrigerant R-134a enters the compressor of a refrigeration machine at a pressure of 140kPa and a temperature of -10°C, and exits at a pressure of 1MPa. The volumetric flow of the refrigerant entering the compressor is 0.23m3/minute. The refrigerant enters the throttling valve at a pressure of 0.95MP and at 30 °C, and exits the evaporator as saturated steam at -18 °C. The adiabatic efficiency of the compressor is 78%. Show the cycle in the T-s diagram. a) Power required to start the compressor b) Calculate the heat withdrawn from the cooled environment in unit time, COPSM=? c) Calculate how much the pressure of the refrigerant drops between the evaporator and the compressor and how much the heat gain is.
In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low velocity. If the nozzle outlets are exposed to atmospheric pressure of 100 kPa. Using Bernoulli equation, determine the maximum velocity to which watercan be accelerated by the nozzles before striking the turbinebuckets.