(6) Steam enters a nozzle at 900°C and 2500 kPa with a velocity of 12 m/s, and leaves at 800°C and 1800 kPa. If the inlet area of the nozzle is 975 cm², the volume flow rate of the steam at the exit (in L/s) is: (a) 1450 (b) 1461 (c) 1473 (d) 1486 (e) 1499

(6) Steam enters a nozzle at 900°C and 2500 kPa with a velocity of 12 m/s, and leaves at 800°C and 1800 kPa. If the inlet area of the nozzle is 975 cm², the volume flow rate of the steam at the exit (in L/s) is: (a) 1450 (b) 1461 (c) 1473 (d) 1486 (e) 1499

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Steam enters a long, horizontal pipe with an inlet diameter of D1 = 16 cm at 2 MPa and 300°C with a…

A: Given data,

Q: Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 6 Mpa, 900…

Q: Saturated vapor enters the turbine at 8.0 MPa and exits 0.008 MPa. The turbine has an isentropic…

A: To find: The electrical power produced. Given: The seam enters the turbine at P1=8 MPa. The exit…

Q: Steam at 0.7Mpa and 250'c expands in a nozzle to 0.1Mpa. Determine the throat and nozzle exit cross…

Q: Steam enters a nozzle at 5Mpa and 400C steadily with a velocity of 75m/s and leaves at 2Mpa and…

Q: Steam at 250 psia and 700°F steadily enters a nozzle whose inlet area is 0.2 ft2 . The mass flow…

A: given dataInlet conditionspressure P1=250 psiaTemperatureT1=700°FInlet area A1=0.2 ft2mass flow…

Q: Cold air enters the mixing chamber at 85°C and 105 kPa at a rate of 0.55 m /s, while warm air enters…

Q: The cross section of the rectangular duct of the heating system is 15 cm x 20 cm (figure shown…

Q: Refrigerant R-134a at 500 kPa and 171 enters an adiabatic nozzle steadily with a velocity of 15…

Q: Q 3. A 5-m-long section of an air heating system of a house passes through an unheated space in the…

A: Given, The average velocity of the hot air, v=5 m/s The cross-section of the rectangular duct, 20…

Q: Steam enters a nozzle at 400°C and 800 kPa with a velocity of 10 m/s and leaves at 375°C and 400 kPa…

A: Data given- T1 = 400 °C P1 = 800 kpa V1 = 10m/s T2 = 375°C P2 = 400 kpa Q = 22.5 KW A = 800 cm2

Q: Refrigerant R-134a at 500 kPa and 171 ⁰C enters an adiabatic nozzle steadily with a velocity of 15…

Q: In a power plant, water vapor with a flow rate of 35 kg / s enters the adiabatic turbine at a…

Q: Air enters a 16-cm-diameter pipe steadily at 200 kPa and 20°C with a velocity of 5 m/s. Air is…

A: solution v1=5m/sR=0.287kPa-m3/kgkd=16 cm(a) volume of flow rate AT INLET , Q1=AV1= π/4 X (0.16)2 X…

Q: Air with an initial density of 1.285 kg/m³ is passed through a compressor with an inlet diameter of…

Q: Air at 100 kPa and 280 K is compressed steadily to 600 kPa and 400 K. The mass flow rate of the air…

Q: Water at the initial pressure of 1 atm and temperature of 15C is flowing through a pump. Final…

Q: A 0.5-m3 rigid tank contains refrigerant-134a initially at 200 kPa and 40 percent quality. Heat is…

A: The volume of the tank = 0.5 m3 The initial pressure of the tank = 200 kPa The quality of steam =…

Q: Steam enters a nozzle at 400°C and 700 kPa with a velocity of 10 m/s, and leaves at 320°C and 150…

Q: Steam enters a turbine steadily at 7 MPa and 600°C with a velocity of 60 m/s and leaves at 25 kPa…

A: Given From steam table

Q: A garden hose attached with a nozzle is used to fill a 10-gal bucket. The inner diameter of the hose…

A: Given: Volume = 10 - gal t = 50 s r1 = 2 cm r2 = 0.8 cm density of water = 1000 kg/m3 = 1000 kg/(103…

Q: (a) A garden hose attached with a nozzle is used to fill a 20-gallon bucket. The inner diameter of…

Q: Refrigerant R-134a at 500 kPa and 120 digits enters an adiabatic nozzle steadily with a velocity of…

Q: Air is compressed polytropically from 101 Kpa and 23 °C and delivered to a tank at 1500 kpa and 175…

Q: The fan on a personal computer draws 0.3 ft3 /s of air at 14.7 psia and 70°F through the box…

Q: Steam enters a long, insulated pipe at 1200 kPa, 250°C, and 4 m/s and exits at 1000 kPa. The…

A: Given data as per question Pressure of steam at entry =1200 kpa Temperature at entry = 250°Cvelocity…

Q: Saturated vapor enters the turbine at 8.0 MPa and exits 0.008 MPa. The turbine has an isentropic…

Q: Q4/Air enters the compressor of a gas-turbine engine at 300 K and 100 kPa, where it is compressed to…

Q: A pump increases the water pressure from 100 kPa at the inlet to 900 kPa at the outlet. Water enters…

A: On using a saturated liquid steam table, the specific volume of saturated water at P1 = 100 kPa is…

Q: Air at 90 kPa and 10oC enters an adiabatic diffuser steadily with a velocity of 180 m/s and leaves…

A: Find , Exit temperature. Concept Apply steady flow energy equation between the inlet and outlet.

Q: Air is to be heated from 15 C to 270 C, as it flows through a tube 25mm diameter at average velocity…

Q: Air is heated as it flows steadily through a constant-are duct of 175 cm^2. It enters at 200 kPa,…

Q: of 0.005 2. pressure of 800 kPa with a velocity of 300 m/s. The nozzle can be assumed to be steady…

A: Answer: (a) The mass flow rate of steam through the system is 0.0516 kg/s. (b) The temperature of…

Q: A cannon fires a shell that causes a projectile to move down the barrel at a velocity of 740 m/s.…

Q: Steam enters a turbine steadily at 7 MPa and 600°C with a velocity of 60 m/s and leaves at 25 kPa…

A: Given: Inlet conditions:P1=7 MPaT1=600°CV1=60 m/sA1=150 cm2Exit Conditions:P2=25 kPaQ=-20…

Q: Air flows steadily through a diverging diffuser. The inlet area of the diffuser is 0.01 m^2, and the…

Q: Air enters a 28-cm diameter pipe steadily at 200 KPa and 20oC with a velocity of 5 m/s. Air is…

Q: A 30 cm diameter pipe carries oil of 800 kg/m3 at 2m/s. At another section, the diameter is 20 cm.…

Q: Air enters an adiabatic nozzle steadily at 300 kPa, 200°C, and 45 m/s and leaves at 100 kPa and 180…

A: a) The mass flow rate m=ρV1=P1A1v1RT1=300×110×10-4×450.287×473=1.09 kgs b)…

Q: A 4-m-long section of an air heating system of a house passes through an unheated space in the…

A: Heat supplied is the heat supplied for the power generation or for the useful work of a machine.…

Q: A 2kg/s of steam expands in a turbine producing 560 kW of power output. The steam enters at a…

Q: A fluid with a pressure of 850kPa, a specific volume of 0.35m3/kg, and a velocity of 170m/s enter a…

A: Given:Inlet velocity=C1=170 m/sHeat lost,Q=30KJ=30×103JWork done,W=48KJ=48×103JOutlet…

Q: Steam at 5 MPa and 400°C enters a nozzle steadily with avelocity of 80 m/s, and it leaves at 2 MPa…

Q: Steam enters a long, horizontal pipe with an inlet diameter of D1 =12 cm at 1 MPa and 300°C with a…

Question

(6) Steam enters a nozzle at 900°C and 2500 kPa with a velocity of 12 m/s, and
leaves at 800°C and 1800 kPa. If the inlet area of the nozzle is 975 cm?, the
volume flow rate of the steam at the exit (in L/s) is:
(а) 1450
(b) 1461
(с) 1473
(d) 1486
(e) 1499

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Answer:

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Answer the questionsWhat is the mathematical model of enthalpy?What is the mathematical model to calculate the flow work?
Water vapor enters a nozzle at 400 °C and 800 kPa, with a speed of 10 m/s, and leaves at 375 °C and400 kPa, while losing heat at a rate of 25 kW. For an entrance area of 800 cm?, determine thevelocity and area of the water vapor at the nozzle outlet in m/s, and cm?, respectively.
Refrigerant R-134a at 500 kPa and 171 enters an adiabatic nozzle steadily with a velocity of 15 cm/s and leaves at 200 kPa and 20 ⁰C. Determine:a) The exit velocityb) The inlet to exit area ratioc) The inlet exit density ratio
Refrigerant R-134a at 500 kPa and 120 digits enters an adiabatic nozzle steadilywith a velocity of 15 cm/s and leaves at 200 kPa and 20 °C. Determine:a) The exit velocityb) The inlet to exit area ratioc) The inlet exit density ratio
On a T-s diagram of Fanno flow, what do the points on the Fanno line represent?
The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6 m3/s air at atmospheric conditions of 20°C and 1 bar (100 kPa) and consumes 300 kW electric power when operating. Air is compressed to a gage pressure of 8 bar (absolute pressure of 900 kPa), and compressed air is transported to the production area through a 15-cm-internal-diameter, 83-m-long, plastic (smooth) pipes with a surface roughness of 0.15 mm. The average temperature of compressed air in the pipe is 60°C. The compressed air line has 8 elbows with a loss coefficient of 0.6 each. In order to reduce the head losses in the piping and thus the power wasted, someone suggests doubling the diameter of the 83-m-long compressed air pipes. Calculating the reduction in wasted power, and determine if this is a worthwhile idea. Considering the cost of replacement, does this proposal make sense to you?
What is the difference between Inlet velocity and superficial velocity?
Air enters a 12-cm-diameter adiabatic duct with inlet conditions of V1 = 150 m/s, T1 = 500 K, and P1 = 200 kPa. For an average friction factor of 0.014, determine the duct length from the inlet where the inlet velocity doubles. Also determine the pressure drop along that section of the duct.
Define mass and volume flow rates. How are they related to each other?
Air in a room at T0= 290 K and P0= 95 kPa isdrawn steadily by a vacuum pump through a 1-cm-diameter,50-cm-long adiabatic tube equipped with a converging nozzleat the inlet. The flow in the nozzle section can be assumed tobe isentropic, and the average friction factor for the duct canbe taken to be 0.018. Determine the maximum mass flow rate of air that can be sucked through this tube and the Machnumber at the tube inlet.
The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6 m3/s air at atmospheric conditions of 20°C and 1 bar (100 kPa) and consumes 300 kW electric power when operating. Air is compressed to a gage pressure of 8 bar (absolute pressure of 900 kPa), and compressed air is transported to the production area through a 15-cm-internal-diameter, 83-m-long, galvanized steel pipe with a surface roughness of 0.15 mm. The average temperature of compressed air in the pipe is 60°C. The compressed air line has 8 elbows with a loss coefficient of 0.6 each. If the compressor efficiency is 85 percent, determine the pressure drop and the power wasted in the transportation line.
Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rateof 100 kgs·1• At a section where the cross-sectional area is 0.5 m2 , thetemperature and pressure are 200 K and 20 kPa, respectively. Determinethe velocity, pressure and cross-sectional area at a downstream sectionwhere the temperature is 350 K. Sketch the flow passage, and show the ·process on a T-s diagram