What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel pipe? The total head loss hL=24.3 m. Water (viscosity of 0.01 kg/m.s and density of 1000 kg/m) water d=2 mm L-45 m

What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel pipe? The total head loss hL=24.3 m. Water (viscosity of 0.01 kg/m.s and density of 1000 kg/m) water d=2 mm L-45 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe experienced a total head loss of 15 m, determine thepressure difference from its starting point to discharge point inkPa.
An oil is being pumped inside a pipe at rate of 5.2m/s-00. The oil density is 905 kg/m3 and the viscosity is 3.4x 10- 2 Pa' s . which pipe diameter should be used to maintain laminar flow le re <_ 2100
A piping system involves sharp turns, and thus large minor head losses. One way of reducing the head loss is to replace the sharp turns by circular elbows. What is another way?
A centrifugal pump was purchased to pump the water from an open tank to a water jet spray cleaner. The spray cleaner requires a pressure of 75 kN/m2 (gauge pressure). The hose that connects the tank to the pump and to the spray jet is 25 m long and has an internal diameter of ¼ inch (0.64 cm). The hose also has a small “kink” in the line that adds some extra head loss with an approximate head loss coefficient of Kkink = 0.3. The spray jet nozzle is located 15 m above the tank liquid surface. Assuming a frictional loss of 0.002 in the line, determine the flow rate and head of the pump. Assume that the spray nozzle has the same diameter as that of the hose and α=1. The centrifugal pump was tested by the supplier before delivery and the performance data is provided in the table below.
CORRECT LETTER PLS 1. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has higher friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is true and JB is false C. BJ is false and JB is false D. BJ is true and JB is true 2.In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has higher friction factorGroup of answer choices A.BJ is true and JB is true B.BJ is false and JB is false C. BJ is false and JB is true D. BJ is true and JB is false 3. In a system with 4 reservoirs and 1 pipe junction, how many continuity equations are formulable?Group of answer choices A. 2 B. 3 C. 5 D. 4 E. 1
Water is pumped from the river through a 45-mmmm-diameter hose having a length of 2.5 mm . The friction factor is f� = 0.028 for the hose, and the gage vapor pressure for water is -98.7 kPakPa. Suppose that hℎ = 1.5 mm . Determine the maximum volumetric discharge from the hose at C� so that cavitation will not occur within the hose. Express your answer to three significant figures.
What does "viscous flow" mean, and what does "head loss through friction" mean? Describe the different small losses that occur.
1. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has higher friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is true and JB is false C. BJ is false and JB is false D. BJ is true and JB is true 2.In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has higher friction factorGroup of answer choices A.BJ is true and JB is true B.BJ is false and JB is false C. BJ is false and JB is true D. BJ is true and JB is false 3. In a system with 4 reservoirs and 1 pipe junction, how many continuity equations are formulable?Group of answer choices A. 2 B. 3 C. 5 D. 4 E. 1
As a piping designer, you were tasked to determine the required water-surface elevation between the reservoir. A 2000 mm diameter,1800 m long concrete pipe with a surface roughness ∈ = 2 mm will be used to carry water between the two reservoirs at 8000 L/s. Assume kinematic viscosity to be ?ѣ = 1.32(10)−6?њ2/?Ѡ and consider minor loses at entrance and exit. NB: Only the frictional factor read from Moody’s diagram will be acceptable.
1) Which of the following statement is NOT correct about piping network? a) In parallel pipes, the flow rate is proportional to its diameter and inversely proportional to its length and friction factor. b) When analyzing the piping network, conservation of mass throughout the system must be satisfied. c) In piping systems with pumps, the Bernoulli equation should be corrected by introducing a kinetic energy correction factor. d) The algebraic sum of head losses for all loops equal to zero. 2) The EGL is always a distance V2/2g above the HGL. True or False
A pump is being used to transport a liquid food product (density = 1000 Kg/m3, viscosity= 1.2 x 10 -3 Pa-s) from a holding tank to a filling machine at a mass flow rate of 2 Kg/s. The liquid level at the holding tank is 5 m above the pump, and the filling machine is 10 m above the pump. There is 100 m of 2 inch nominal diameter sanitary pipeline (assume: commercial steel) between the holding tank and the filling machine with one open glove valve and three medium sweep 90oelbows in the system. Determine the theoretical power requirement of the pump if the efficiency is 75%. Answer: 234 Watts. Show the solution.
what is the pressure drop per meter for water flowing at 6 m/s through a 8 x 4 cm annulus? (dinner = 4 cm , douter = 8 cm)