SAE 10 oil at 20°C (y = 8.52 kN/m³, p = 860 kg/m³, u = 8.14 x 10-2 N-s/m2) is to flow through a 300-m level concrete pipe. What size pipe will carry 0.0142 m2/s with a pressure drop due to friction of 23.94 kPa? Ans. 156 mm

SAE 10 oil at 20°C (y = 8.52 kN/m³, p = 860 kg/m³, u = 8.14 x 10-2 N-s/m2) is to flow through a 300-m level concrete pipe. What size pipe will carry 0.0142 m2/s with a pressure drop due to friction of 23.94 kPa? Ans. 156 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. A research experiment requires a laminar flow of water at 20°C through a 120mm diameter pipe at a…

Q: For Oil (SG = 0.86, p = 0.025 Ns/m2) flow of 0.3 m3/s through a round pipe with diameter of 500 mm,…

A: Given data: The specific gravity of oil, SG = 0.86. Dynamic viscosity of the oil, µ = 0.025 N·s/m2.…

Q: 3 Water with a viscosity of p=0.02 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30…

A: Given : - viscosity , μ = 0.02 kg/m .s density , ρ = 1000 kg/m3…

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

A: Given question belongs to subject Fluid Mechanicas from Topic Flow through pipes.

Q: Fluids Question A smooth copper tube 50 ft long and 2 1/2 in.‐diameter carries a water flow at 60°F…

Q: find the head loss in the pipe using Darcy weishbach, manning and hazen Williams (remember to watch…

Q: A 3-ft-diameter duct is used to carry ventilating air (p = 2.373 x 10-3 slugs/ft,v = 1.57 × 10-4 ft…

Q: Q2: Water at 20°C (p= 998 kg/m, µ= 1.003 x10- N.s/m?) flows in a long horizontal commercial-steel 6…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: A new steel pipe, 15 cm in diameter and 1200 m long carries 0.020 m^3/s of heavy fuil oil with S=…

Q: Oil, SG = 0.88 and ν = 4 E-5 m2/s, flows at 400 gal/minthrough a 6-in asphalted cast iron pipe. The…

A: Given and assumed data: The velocity of the flow is

Q: For fl ow of oil [μ = 0.1 kg/(m ? s), SG = 0.9] through along, straight, smooth 5-cm-diameter pipe…

A: Given Data: The viscosity of the oil is µ = 0.1 kg/m-s. The specific gravity of the oil is G = 0.9.…

Q: A cast iron pipe of equilateral triangular cross sectión with side length of 20.75" has water…

A: Given Data : Sides of equilateral triangle = 20.75 inch Flowrate = 6000 gallon per minute…

Q: Water with a viscosity of p=0.031 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30…

A: GIVEN :- viscocity of water : μ=0.031kg/m.sdiameter of tube : D=1.5 mmdensity of water :…

Q: Air at 200°F flows through a pipe with 0.5 inch diameter at a rate of 0.08 Ibm/s. What is the flow…

A: The temperature of the air is T=200°F. The diameter of pipe is D=0.5 in. The flow rate of the air is…

Q: Considering pipe loss only, what difference in elevation between two tanks 800 ft apart will deliver…

A: Given Data Length of pipe is : L=800 ft Flow rate is : Q=1.10 ft3/s Temperature of fluid is :…

Q: A 36-in-diameter pipeline carries oil (SG = 0.89) at1 million barrels per day (bbl/day) (1 bbl = 42…

A: Given data as per question Pipe diameter = 36 in Specific gravity of oil =0.89 flow rate = 1 million…

Q: 8. A Venturi meter is to be fitted to a 60 cm diameter pipe, in which the maximum flow is 0.4 m/s…

Q: A pump delivers 1 hp to a water at 68°F flowing in a 10-in-diameter horizontal, cast iron pipe at V…

Q: Q2) For laminar flow conditions. Calculate the pipe diameter should be installed to carry 0.022m/s…

A: Given, Flow rate , Q = 0.022 m3/s Kinematic viscosity of oil , v = 0.00021m2/s Specific gravity =…

Q: SAE 10 oil at 20°C (γ = 8.52 kN/m , ρ = 860 kg/m , μ = 8.14 × 10 Ns/m ) is to flow through a300-m…

A: Given: The specific weight of oil, S = 8.52 kN/m3 The density of oil = 860 kg/m3 The dynamic…

Q: Prob. 2: Water at 20°C flows for 1 mi through a 3-in-diameter horizontal wrought-iron pipe at 0.557…

Q: A 4in ductile iron pipe carries 0.20 ft3/s of glycerin (SG=1.26) at 100°F. Is the flow laminar or…

Q: The Alaska Pipeline in the chapter opener photo has a designflow rate of 4.4 E7 gallons per day of…

A: Given Q=4.4x107 gallons per day Q=(4.4x107x(1/264))/(24x60x60) Q=1.93 m3/s Part a The velocity of…

Q: roperie PAmn nower andeeieney mey. Problem: Determine the head of water H. Flow rate Q=5 V/s, =20 m,…

A: NOTE:- Here I use Colebrook, churchill correlation to find out the friction factor for turbulent…

Q: Water fl ows through a straight 10-cm-diameter pipe at adiameter Reynolds number of 250,000. If the…

A: Given, D = 10 cm =0.1 m Re = 250,000 So the flow is turbulent. Pipe roughness is =0.06 mm=0.06x10-3…

Q: 89. Haka at e0°c (p=998 kg/m3 = l1003 X10 in %3D N.S/m2) long harizontaf flows COMMercial- steel 6…

A: Venturimeter is a practical application of Bernoulli's equation. Venturimeter consists of basically…

Q: Considering pipe loss only, how much head is required to deliver 0.222 m 3/s of heavy fuel oil at…

Q: Q2: Water at 20°C (p= 998 kg/m, u= 1.003x10-3 N.s/m²) flows in a long horizontal commercial-steel 6…

A: Venturimeter is a practical application of Bernoulli's equation. Venturimeter consists of basically…

Q: SAE 10 oil at 20°C (ρ = 869 kg/m , μ = 8.14 × 10 N·s/m ) flows in a 200-mm-diameter pipe. Find the…

Q: What is the Reynolds number for a straight and perfectly smooth pipe of length 500 m and diameter…

A: Consider Q is the mass flow rate, ρ is the density of fluid, V is the velocity of the fluid and A is…

Q: Q2: Water at 20°C (p= 998 kg/m, u=1.003x103 N.s/m) flows in a long horizontal commercial-steel 6 cm…

A: Venturimeter is a practical application of Bernoulli's equation. Venturimeter consists of basically…

Q: Water with a viscosity of u=0.01 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30 m…

A: This question is solved with the help of Bernoulli's equation, Bernoulli's equation is based on the…

Q: Water at 20 ° C is to be siphoned through a tube 1 m longand 2 mm in diameter, as in Fig. . Is there…

A: Draw the diagram for the problem. Here, the points 1 and 2 indicate the points in the siphon as…

Q: Oil, with p-950 kg/m' and v=2x10* m/s ,flows through a 30-cm-diameter pipe 100 m long with a head…

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f=0.0225) oflength…

Q: What size of new cast iron pipe (roughness of 0.00026) is needed. to transport 550 L/s of water for…

A: Given data as per the question Q=550 =0.550 m3s Length of pipe =1 km =1000 mhead loss =3m

Q: A SAE 30 oil at 38°C flows through a 0.01-m diameter, with a 4-m long pipe which is inclined at a…

A: Fluid = SAE 30 Diameter, D = 0.01 m Length , L = 4 m angle of pipe with horozontal, θ = 31 degree…

Q: The water is delivered with piping system given in the figure below. The levation difference between…

A: Given: The difference in elevation Z2 – Z1 = 143.55 m The density of water, ρ = 998 kg/m3 The…

Q: 9. Hata at 20°C 3 ,=1 003 X16 în (P=998 kg/m³ %3D N.S/m2) long horizontaf flows CONMercial- steel 6…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Gasoline ( v= 4.06 E-7m^2/s) flows at 0.9L/s through a 100mm diameter pipe. Describe the type of…

Q: 2 Hata at 20°G (P=998 kg/m3 ,l= 1. 003 X10 N.S/m2) COMMeRCial-steel 6CM diamoter pipe which…

A: Venturimeter is a practical application of Bernoulli's equation. Venturimeter consists of basically…

Q: 9. Hata at 20°C CP =998 kg/m3 N.S/m2) ,l=l. OD3 X10 1ong horizontaf pipe 4=1.003 XiO %3D in…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Water at 20°C fl ows through a pipe at 300 gal/min with afriction head loss of 45 ft. What is the…

A: GIVEN:Q=300gal/minhead loss h=45ft

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

SAE 10 oil at 20°C (y = 8.52 kN/m³, p = 860 kg/m³, u = 8.14 x 10-2 N-s/m2) is to flow through a
300-m level concrete pipe. What size pipe will carry 0.0142 m2/s with a pressure drop due to friction of
23.94 kPa?
%3D
8.6
Ans. 156 mm
8.G

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Considering pipe loss only, how much head is required to deliver 0.222 m³/s of heavy fuel oil at 38°C through 914 m of new cast iron pipe, 300 mm inside diameter? Use ε=0.00024 m. (ANSWER MUST BE = 41 m)
Oil of density 950 kg/m³ and viscosity 1E-2 Pas is to be pumped 10 through a pipeline and the pressure drop must not exceed 2E5 Pa. What is the minimum diameter of pipe which will be suitable, if a flowrate of 50 tonne/h is to be maintained? Assume the pipe wall to be smooth. A. 0.025 mB. 0.175 mC. 0.855 mD. 0.008 m
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
Glycerin, sg = 1.26 and μ = 1.49 Pa-s, flows through a 600-mm Ø pipe at 85 liters per second. a. What is the Reynold’s Number? b. What is friction factor? c. What is the critical velocity?
Determine the size of clean wrought-iron pipe (e=0.046 mm) required to convey 250 L/s of oil, =1x10-5 m2 /s), 3000 m long with a head loss of 25 m.N/N. [ Hint: Use Colebrook equation for transitionally rough pipe (whatever is the calculated f, that is final and no need to check if the pipe is smooth or rough).
Oil, SG = 0.88 and ν = 4 E-5 m2/s, flows at 400 gal/minthrough a 6-in asphalted cast iron pipe. The pipe is 0.5 milong and slopes upward at 88 in the flow direction. Computethe head loss in ft and the pressure change.
A Keystone Pipeline has a diameter of 36 inches and a design flow rate of 590,000 barrels per day of crude oil at 40ºC. Estimate the pump horsepower required if the length of the pipe is 2.9 mile(s). The pipe material is new steel. For crude oil at 40ºC, take μ ≈ 0.0053 kg/m-s ÷ 47.88 = 0.0000111 slug/ft-s. The density, with SG = 0.86, is 0.86(1.94) = 1.67 slug/ft3. Take f ≈ 0.0155.
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
It is desired to deliver 60 m3/h of water at 20°C through ahorizontal asphalted cast iron pipe. Estimate the pipe diameterthat will cause the pressure drop to be exactly 40 kPaper 100 m of pipe length.
EthanoL at 20c(8 = 789 kglm, M=00012 152/m.s) flow at a horizontal cast-iren pipe with L 12m 125 apm through and d= 5 cm , Neglecting entrance effect > estimaite A- the wall shear stress 3- tu precent reduction in friction factor if the pipe walls are polished to a smooth surface. ?
A Keystone Pipeline has a diameter of 36 inches and a design flow rate of 590,000 barrels per day of crude oil at 40ºC. Estimate the pump horsepower required if the length of the pipe is 2.9 mile(s). The pipe material is new steel. For crude oil at 40ºC, take μ ≈ 0.0053 kg/m-s ÷ 47.88 = 0.0000111 slug/ft-s. The density, with SG = 0.86, is 0.86(1.94) = 1.67 slug/ft3. Take f ≈ 0.0155. Answer is in hp. Last answer was wrong! please help!
Water at 20°C fl ows by gravity through a smooth pipe fromone reservoir to a lower one. The elevation difference is 60 m.The pipe is 360 m long, with a diameter of 12 cm. Calculatethe expected flow rate in m3/h. Neglect minor losses.