What will be the rotational speed of a wind turbine that generates a power of 5MW at 140km/hr wind speed? The turbine is having a blade length of 50 meters and the tip speed ratio value of 3.44? 25.56 rpm 75.75 rpm 100.32 rpm O 51.12 rpm

What will be the rotational speed of a wind turbine that generates a power of 5MW at 140km/hr wind speed? The turbine is having a blade length of 50 meters and the tip speed ratio value of 3.44? 25.56 rpm 75.75 rpm 100.32 rpm O 51.12 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

To avoid the bulky tower and impeller and generator inthe HAWT of the chapter-opener photo, we could insteadbuild a number of Darrieus turbines of height 4 m anddiameter 3 m. (a) How many of these would we need tomatch the HAWT’s 100 kW output for 15 m/s wind speedand maximum power? (b) How fast would they rotate?Assume the area swept out by a Darrieus turbine is twothirdsthe height times the diameter.
A propeller type, horizontal axis wind turbine having following windcharacteristics: Speed of the wind 10 m/s at 150 C, The turbine has diameterof 120 m and its operating speed is 40 rpm at maximum efficiency.Calculate (i) the total power density in the wind stream (ii) the maximumobtainable power density assuming wind power coefficient as 40% (iii)total power produced in kW (iv) Maximum thrust and axial thrust.[Ans: 613 W/m2 , 2771 kW, 6930 kW, 619.9510 kN, 897 kN]
Estimate the amount of power generated by a wind turbine having a powercoefficient of 0.37 given the annual average wind speed:Rotor diameter = 125 mCenter of rotor at an elevation 160 m above the surface level.Location: Oklahoma City, OK
For D400 Wind Power, a) what power output should be able to supply from the 24v D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will be the output power be? c) According to the perfomance graph what is the maximum power you can obtain from the 24v D400? d) There is a possibility of installing the turbine on top of a 20m high mast instead.Assuming that Z = 0.012, what would you except the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m
An electric utility decides to add 50 MW of wind generation to its system. If the individual units are to be rated at 2 MW in a 13-m/s wind at standard conditions and have efficiencies Cp = 0.32, ηm = 0.94, and ηg = 0.96, what is the required swept area of each rotor?
A large turbine is rated at 2500 kW at standard conditions (0°C and 101.3 kPa). What would be its rated power at the same rated wind speed if the temperature were 20°C and the turbine was located at 1500 m above sea level.
A 5 MW turbine is developed under an effective head of 320 m. The turbine efficiency is85%. Velocity coefficient of the nozzle is 99%.(a)Select which is the appropriate turbine based on effective head. (b)What should be the wheel diameter in meters assuming it is 12 times the diameter of the jet?
A 1:10 model of a Francis turbine developed 0.5 kW under a head of 2.5 m at 480 rpm. The physical data are r1=1.5m, r2 = 0.4m, α1=15°, β2=135°. Find the speed of the prototype at a head of 20m.
[5] A Francis turbine operates at its maximum efficiency point at h0 = 0.94, corresponding to a power specific speed of 0.9 rad. The effective head across the turbine is 160 m and the speed required for electrical generation is 750 rev/min. The runner tip speed is 0.7 times the spouting velocity, the absolute flow angle at runner entry is 70 deg from the radial direction and the absolute flow at runner exit is without swirl. Assuming there are no losses in the guide vanes and the mechanical efficiency is 100%, determine (i) the turbine power and the volume flow rate; (ii) the runner diameter; (iii) the magnitude of the tangential component of the absolute velocity at runner inlet; (iv) the axial length of the runner vanes at inlet.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m. The runner blade angles are ?2 = 71.4° and ?1 = 15.3° at the turbine inlet and outlet, respectively. The runner rotates at n. = 160 rpm. The volume flow rate at design conditions is 80.0 m3/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (MW) and required net head (m).
The nominal power of the wind turbine is 3MW at wind speed 11.5m/s, generator efficiency is 94%, gear box efficiency is 0.75, power coefficient of blades is 0.59. What would be the diameter of the rotor
Turpomachinery A multi-jet Pelton turbine of 1.47 m wheel diameter operates under a head of 200 m and has a specific speed of Ns = 42. The jet/wheel diameters ratio is 0.113. The wheel efficiency is 88% and the velocity coefficient of all nozzles is Cv = 0.95. The speed factor is (Φ=0.47). Determine: Your answer The bucket angle The bucket speed The jet velocity The developed power