What would be the effect of an increase in the value of the inner radius of the capillary tube to the calculated surface tension of a liquid when all other variables are kept constant? (No calibrating liquid is used.) * The density of the liquid will decrease. The surface tension of the liquid will decrease. O The density of the liquid will increase. The surface tension of the liquid will increase

What would be the effect of an increase in the value of the inner radius of the capillary tube to the calculated surface tension of a liquid when all other variables are kept constant? (No calibrating liquid is used.) * The density of the liquid will decrease. The surface tension of the liquid will decrease. O The density of the liquid will increase. The surface tension of the liquid will increase

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 96P: (a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in...

See similar textbooks

Similar questions

Is there a limit to the height to which an entrainment device can raise a fluid? Explain your answer.
Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
Could capillary action be used to move fluids in a "weightless" environment, such as in an orbiting space probe?
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
Construct Your Own Problem Consider a coronary artery constricted by arteriosclerosis. Construct a problem in which you calculate the amount by which the diameter of the artery is decreased, based on an assessment of the decrease in flow rate.
(a) Using Bernoulli's equation, show that the measured fluid speed v for a pitot tube, like the one in Figure 12.7(b), is given by v=( 2gh)1/2 , where h is the height of the manometer fluid, is the density of the manometer fluid, is the density of the moving fluid, and g is the acceleration due to gravity. (Note that v is indeed proportional to the square root of h, as stated in the text.) (b) Calculate v for moving air if a mercury manometer's h is 0.200 m. Figure 12.7 Measurement of fluid speed based on Bernoulli's principle. (a) A manometer is connected to two that are close together and small enough not to disturb the flow. Tube 1 is open at the end facing the flow. A dead spot having zero speed is created there. Tube 2 has an opening on the side, and so the fluid has a speed V across the opening; thus, pressure there drops. The difference in pressure at the manometer is 12v22 , and so h is proportional to 12v22 . (b) This type of velocity measuring device is a Prandtl tube, also known as a pitot tube.
Does atmospheric pressure add to the gas pressure in a rigid tank? In a toy balloon? When, in general, does atmospheric pressure not affect the total pressure in a fluid?
Calculate the Reynolds numbers for the flow of water through (a) a nozzle with a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when the nozzle is attached to the hose. The flow rate through hose and nozzle is 0.500 us. Can the flow in either possibly be laminar?
Water pressure inside a hose nozzle can be less atmospheric pressure due to the Bernoulli effect. Explain in terms of energy how the water can emerge from the nozzle against the opposing atmospheric pressure.
A container of water has a cross-sectional area of A=0.1m2 . A piston sits top of the water (see be following figure). There is a spout located 0.15 m from the bottom of tank, open to the atmosphere, and a stream of water exits the spout. The cross sectional area of the spat is As=7.0104m2 . (a) What is the velocity of the water as it leaves the spout? (b) If the opening of the spout is located 1.5 m above the grand, how far from be pout does water hit the floor? Ignore friction and dissipative forces.
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
Water pressure inside a hose nozzle can be less than atmospheric pressure due to the Bernoulli effect. Explain in terms of energy how the water can emerge from the nozzle against the opposing atmospheric pressure.