When a bar with the hexagonal cross sectionshown in Fig. (a) is subjected to a torque T,numerical analysis shows that the maximumshear stress in the bar is Tmax =5.7T|3.Determine the percentage loss in strength thatresults when a circular bar of diameter dismachined into the hexagonal shape shown inFig. (b).Location of Tmax-(a)(b)FIG. P3.53

Answered: Image /qna-images/answer/7732d049-1f07-44c5-936b-3e460519f8d7.jpg

When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical analysis shows that the maximum shear stress in the bar is Tmax = 5.7 T/. Determine the percentage loss in strength that results when a circular bar of diameter dis machined into the hexagonal shape shown in Fig. (b).

When a bar with the hexagonal cross section shown in Fig. (a) is subjected to a torque T, numerical analysis shows that the maximum shear stress in the bar is Tmax = 5.7 T/. Determine the percentage loss in strength that results when a circular bar of diameter dis machined into the hexagonal shape shown in Fig. (b).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive stress in the punch is limited to 50 ksi. calculate the thickness maximum of the plate in which a hole of 2.5 inches in diameter can be drilled. The figure is in the attached image.
Please show all work!
Please solve d through g
(a) Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was pressurized internally Pi = 56 MPa and externally Po= 26 MPa. Analyse: i. The hoop stress and radial stress on internal and external surface of the cylinder. ii. The hoop stress and radial stress at r= 115 mm. iii. The maximum and minimum shearing stress. iv. Sketch the distribution of hoop stress and radial stress along the cylinder wall. Po Figure 1.1 The thick cylinder
Derive the following equation for computing shear stress in a solid bar along an oblique plane with angle B with respect to the vertical plane. The bar is subjected to centric axial loading. sin 0 cos 0 T = Ao
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 14 mm, and the rod length was 440 mm. When the applied torque reached 225.3 N-m, a shear strain of 2105 microradians was measured in the specimen. What was the angle of twist in the specimen? Calculate the shear stress in the specimen. Answer: T= 418.16 Use Hooke's Law to calculate the shear modulus of the specimen. answer: MPa G = i MPa
8.8 (A/B). Opposing axial torques are applied at the ends of a straight bar ABCD. Each of the parts AB, BC and CD is 500 mm long and has a hollow circular cross-section, the inside and outside diameters being, respectively, AB 25 mm and 60 mm, BC 25 mm and 70 mm, CD 40 mm and 70 mm. The modulus of rigidity of the material is 80 GN/m³ throughout. Calculate: (a) the maximum torque which can be applied if the maximum shear stress is not to exceed 75 MN/m²; (b) the maximum torque if the twist of D relative to A is not to exceed 2. [E.I.E.] [3.085 kNm, 3.25 kNm]
Why did it became 4F/A from F/A, in (a)
Please present drawings/FBD’s illustrating your solution.