When a bolt is in tension, the load on the nut is transmitted through the root area of the bolt which is smaller than the shank area. A bolt 24 mm in diameter (root area = 353 mm) carries a tensile load. Find the percentage error in the calculated value of the stress if the shank area is used instead of the root area.

When a bolt is in tension, the load on the nut is transmitted through the root area of the bolt which is smaller than the shank area. A bolt 24 mm in diameter (root area = 353 mm) carries a tensile load. Find the percentage error in the calculated value of the stress if the shank area is used instead of the root area.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 73AP: Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m...

See similar textbooks

Similar questions

A 100-N weight is attached to a free end of a metallic wire that hangs from the ceiling. When a second 100-N weight is added to the wire, it stretches 3.0 mm. The diameter and the length of the wire are 1.0 mm and2.0 m, respectively. What is Young’s modulus of the metal used to manufacture the wire?
An aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?
Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
Normal forces of magnitude 1.0106N are applied uniformly to a spherical surface enclosing a volume of a liquid. This causes the radius of the surface to decrease from 50.000 cm to 49.995 cm. What is the bulk modulus of the liquid?
Check Your Understanding A 2.0-m-long wire stretches 1.0 mm when subjected to a load. What is the tensile strain in the wire?
Can Young’s modulus have a negative value? What about the bulk modulus?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
The bulk modulus of a material is 1.01011N/m2 . What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 107N/m2 ? Assume that the force is applied uniformly over the surface.
A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
A company is testing a new material made of recycled plastic for use in construction. Figure P14.48 is a graph of the stress as a function of strain for this material. Find Youngs modulus for this material and compare your result with the data for conventional building materials listed in Table 14.1.
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Check Your Understanding Find the compressive stress and strain at the base of Nelson’s column.