When a fulcrum is in the middle the force and distance are___. A. The same at both ends B. Multiplied by 2 C. Half of what they used to be

Q: Daw the Free buly Dingram

A: Free body diagram of given figure

Q: Poisson's ratio of the rod

A: Given; Find Poisson's ratio of the rod material ?Where,  Metallic rod length, l=500 mmDia,d=50…

Q: Sommerfeld number of the bearing

A: Given;A hydrodynamic  journal bearing is subjected toLoad= 2000 NRotational speed=2000 rpm bearing…

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: differentiate between shaper and planer machine any six difference

A: A shaper is a reciprocating type machine used to produce horizontal, vertical, and inclined surfaces…

Q: rope around the post?

A:

Q: يمكننا إدخال رقم صفحة من خالل 0 0 ( Footer Both Header and Footer > Header None of the above > O

A: In the Microsoft we can enter page number in the footer. Header

Q: Q3: (a) describe the location and function of the following: i. Gudgeon pin ii. Rod shank ii.Large…

A:

Q: Sketch the proper end shape of a soapstone that is to beused for marking metal.

A: The design of the work metal is marked with soapstone & chalk line to ensure appropriate…

Q: A B - 3 ft - 6 ft - 3 ft 2 in. 6 in. 2 in. I in. in.

A:

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: the force needed to deflect 1 inch of length is called

A: The force needed to deflect one inch of length can be called as stiffness.

Q: A frame is being raised on a pivot point. a crane lifts the frame and shows 315 165 at 45⁰. How much…

A:

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: Short axles on the machine are called _____. a. Shaftings b. Shaft c. Axle d. Spindle e. Key

A: Define all the entities given to find the most accurate option amongst all.

Q: can make it in Solidwork

A: Given Structure To find 3D model

Q: How to draw an IV cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: Facing operation is performed on? A. Drilling machine. B. Sawing machine. C. Milling machine. D.…

A: Facing operation is performed on lathe machine.

Q: 2 in. plywood in. 24 in. 3월 in. 2x4 2 x 4 lž in. 1 in. --- 1/2 1/2 1/2

A:

Q: , the minimum metric specification required for the bolt is

A: Given, From the given shows,  Three bolt system having, Shear yield strength,σyt=200 MPaFOS=…

Q: If a force doubled, impulse will triple. True or false

A:

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: H.W praw load dingram alesfanding to the given-Shar dingram? 2nd (urve 10 2nd Garve sfin -10 Im Im

A: BMD(Bending moment diagram) is a diagram representing the variation of bending moment along the…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: On increasing the value of rake angle, the strength of tooi.

A: Rake angle is defined as the angle between the normal line to the workpiece and the edge of the…

Q: The tool used for marking center is __________. a.   Steel rule   b.   Divider   c.…

A: Solution:

Q: The largest soft aluminum tubing that may bent by hand is ________________ -inch outside diameter. *

A: Solution:

Q: the bolt is

A:

Q: Steps how to draw a needle of a cannula using SOLIDWORK

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: what maximum angle can the ramp make with the horizontal before the block starts to slip down?

A:

Q: with proper value

A:

Q: 8. is used most frequently when lifting or setting down loads, but they also occur in carrying,…

A: The answer to this question is Manual handling. It is a process in which a person uses part of his…

Q: When utilizing pins to assemble rigging components, the "grip" area of the pin is  A. diameter of…

A: Rigging pins are generally measured by the diameter and the grip length. Given diameter can be…

Q: bolts required for an

A:

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Q: ricated from a steel alloy g service use, the plate is

A: given:surface roughness kt=55MPamtensile stress σ=200MPaY=1

Q: First pulley ley

A: The tensions in the rope on the sides of pulley will be different due to rotational inertia. Three…

Q: B. A machine - part needs 14 bolts a How many bo43 are needed For 25 nachine -parts? b. wnat is the…

A:

Q: Define Iron Stirrups

A: Given Stirrups To find Iron stirrups

Q: resistance to motion caused by the shoveling

A: Given: Q= 12 ft3/s V=14 ft/s specific weight =5.5 lb/ft3 TO determine: resistance to motion

Q: The maximum radial load

A: Given: The dynamic load capacity of 6306 bearing is 22 KNMaximum radial load it can sustain to…

Q: 21. How to hold the hammer handle whlie driving the nail? a.Middle of the handle. bi Anywhere in…

A: Hold the nail with the thumb and first finger. Hold the handle nearer the hammer head for better…

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: ow bar evaluate use th

A:

Q: rope is wrapE

A:

Q: Prob 3: Form lumbers are: 2 x 2 3 pcs 5 pcs 12 pcs 2x 4" x 12 cost is $ 52/6d ft, if How much will…

A:

Q: Define the term Angle of Repose

A: The slope of cut and fill at the excavation site which is measured in feet of horizontal to feet of…

Q: What is the depth, minor diameter, width of crest and root for a bolt 1⁄2 X 20 UNF

A: UNF = Unified National Fine Screw Thread.   The Nominal Major Diameter and Threads-per-inch (Pitch)…

Q: [- hammer is used on domed circular works

A: planishing hammer has a round face, which is used on domed circular work