When measured the moment of force, it need tunneling point * O True False

Q: n fluid mechanic, what is dimensional analysis and what do i required to do a dimensional analysis f...

A: Given Dimensional analysis To find Importance of dimensional analysis in fluid mechanics Importance ...

Q: Methyl acrylate is flowing at 283.15 k at shear of 0.0525 N/m2. Determine the velocity at which the ...

A:

Q: The truss to the right is comprised of members with cross sectional area A = 3 in', length of 12 inc...

A:

Q: Calculate the power dissipated in Rs, as shown in Fig. (1). R1-6n R2-3n R3-6 n R4-2 n + E= 19.8 V Rs...

A:

Q: Air compressor takes air of mass flow rate (9kg/min) at (100kPa) and (300K). Air leaves the compress...

A:

Q: Which of the following statement about carbon dioxide is not true? a. CO2 , levels are highest when ...

A: Solar and wind energy are examples of renewable energy sources that do not emit carbon dioxide or ot...

Q: A submarine moves horizontally in sea and has its axis 15 m below the surface of water. A pitot-tube...

A: The difference in the mercury level is, x=170 mm The density of mercury is, ρm=13600 kgm3 The densit...

Q: 1. What is the main function of a flywheel in an engine? 2. In what way does a flywheel differ from ...

A:

Q: Given a shear stress of Txy = 5000 psi and a shear modulus of G 1.15 x 107 psi, find the shear strai...

A:

Q: A carnot engine is working between the temperature range of 227°C and 127°C. If the heat absorbed by...

A: As given in question, Higher temperature in carnot cycle = TH = 227 oC = 500 K Lower temperature in ...

Q: Prob. 2.3-10. A rod AB, whose unstretched length is L, is originally oriented at angle 0 countercloc...

A:

Q: State and explain the simple change you would have to make to your FLUENT setup to see a shock in th...

A: Ansys fluent is a cae software package of ansys which uses finite volume method to solve simulation ...

Q: How can a DC motor be made to operate above its base speed?

A: Given DC motor To find To operate above the base speed  

Q: A copper bar AB with a length 25 in. anddiameter 2 in. is placed in position at room temperaturewith...

A: Length of copper bar,l=25 inDiameter of copper bar AB=d=2 inGap,δ=0.008 inSpring constant,K=1.2×106 ...

Q: 150 kN 50 kN/m 20 kNm B 25 m 5 m 5 m

A:

Q: A pelton wheel is supplied with water under a head of 100 m at the rate 1000 litres/s. The bucket de...

A: Given that, H=100 m; Q=1000 L/s=10001000=1 m3/s ;ϕ=180-160=20° ;u=20 m/s

Q: What are the few factor that can influence the magnitude of discharge coefficient C beside diameter....

A: Nozzles and orifice plates have two separate applications. The first is flow restriction, where prec...

Q: A rectangular block 100 mm x 150 mm has a hole with diameter 60 mm at the center. The hole tolerance...

A:

Q: The higher temperature of a refrigerating system operating at a Reverse Carnot Cycle is 240 °F and t...

A: Higher temperature in the cycle, TH=240oF=388.706 KLower temperature in the cycle, TL=266.483 KRefri...

Q: Badr Al Sama Hospital pharmacy decided to deploy a robot to vend medicines to the patients. It is we...

A: There are several drives that can help vend light weight medicines to patients. The use of pneumatic...

Q: A creep experiment was performed on the mesenchymal cell with a 4.5 N force. Knowing that cellular m...

A:

Q: An electric motor of mass 500 kg is placed on springs with statical displacement of 0.6 cm. The rota...

A:

Q: Determine the constant torque that must be applied to a 50-kg flywheel, with radius of gyration 45 c...

A:

Q: he nord stream 2 is a pipeline network from used to pump and transport Russian oil to germany. 29286...

A: Given:Flow rate of oil, Q=29286 gallons/min1 gallons=0.160544 ft3Q=4701.69 ft3/minQ=78.3615 ft3/s  1...

Q: The assembly is subjected to a tension force P = 2500 N. If these cables are arranged in a parallel ...

A:

Q: Block A supporting another block B is pulled along a rough horizontal plane by a horizontal force P....

A:

Q: Mr. Jae Yeong wants to put up a plant rack for his mini garden using a recyclable material from neig...

A:

Q: Find the real valued general solution o

A: Find the general solution.

Q: 5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define ...

A:

Q: As an industrial engineer, in what ways could you incorporate the use of flow process diagram in you...

A: There are a lot of ways in which I can use a process flow diagram in my daily life as an Industrial ...

Q: What is the magnitude of the reaction force at joint c and a in the x and y direction?

A: To find: The reaction forces at A and C: Ax = ? Ay = ? Cy = ?

Q: One kilogram of air is compressed from a volume of 1.0 m and a pressure of 100 kPa to a volune of D....

A: Here diven Mass of the air m=1 kgInitial volume =V1=0.547 m3Initial pressure P1=400kpaFinal volume V...

Q: Determine the Miller Index of plane of the given plane in an HCP crystal? (1070) → (10 – 10 ) ► GREE...

A: find the miller index of green plane For Given HCP cystal

Q: The allowable tensile stress for a ½ bolt of thread length 7/32 inches is 30000 psi. The allowable s...

A:

Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area...

A:

Q: diameter of 8 cm and a wall thickness of 5.5 mm. It is covered with a 9-cm layer of insulation hävin...

A:

Q: A steel specimen is subjected to a tensile force of 400 kips. If the Poisson's Ratio is 0.20, and th...

A: Given:- F=400kips V= 0.20 E=2.8x107psi  

Q: ate is 30 kg/min. Determine a) the tons of refrigeration b) the power required c) the COP.

A:

Q: Home work 1 What is the use of a pulley?

A: As per our guidelines, we are supposed to answer only first one question in case of multiple questio...

Q: A 4.0 kg mass, ml, hangs from a rope that runs over a massless frictionless pulley and is connected ...

A:

Q: Assignment 1 1. Determine the positive root of f (x) x3 + 2x – 2 = 0 using the Newton- Raphson metho...

A:

Q: 7. What is the slope of the line perpendicular to the line joining P,(-2,3) and P,(0,9)? 1 A) -3 C) ...

A: Answer: The slope of the line perpendicular to the line joining given two points is (1/3). Hence, th...

Q: new temperature scale called the N-scale is to be defined using the ice point, at 0°C as 50°N and th...

A:

Q: The pin P slides in the disk slot and also in the spiral slot cut in the reference frame and defined...

A: The pace at which the angular location of a rotating body changes is known as angular velocity. The ...

Q: 3. A 60 pound force is attached to the 90° weightless bar ABCD at point B as shown below. The bar is...

A:

Q: 4- Single acting single cylinder compressor with diameter (15cm) and stroke length of (22.5cm).The a...

A:

Q: An oil radiator has an outside surface area of 0.18 m2 and operates at a surface temperature of 85 d...

A:

Q: polypropylene PP rod attached ceiling 200 mm tick 25 mm width,3 mm length in loaded with 30 kg . fin...

A: Given data Thickness of Polypropylene rod = 200 mm Width = 25 mm Length = 3 mm Load = 30 kg Time = 2...

Q: A bracket ABCD having a hollow circularcross section consists of a vertical arm AB (L 5 6 ft),a hori...

A:

Q: f a thermometer is taken from a room in which the temperature is 750 into the open, where the temper...

A: Given:Temperature of room, Tr=75o COpen atmospheric temperature, To=35o CAfter 30 s reading=65o C

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.