Correct and complete solution please don't copy The truss to the right is comprised of members with3 in', length of 12 inches, and Young'scross sectional area A =Modulus E = 30x10 psi. The applied displacements at node 6 areu=0.57 in and v=0.45 in the directions indicated.%3DCalculate the stress in clement , indicate tension (T) orcompression (C).325302593030

Answered: Image /qna-images/answer/c4f7a709-6a9b-4a34-ba5b-1dac0b397637.jpg

The truss to the right is comprised of members with cross sectional area A = 3 in', length of 12 inches, and Young's Modulus E = 30x10 psi. The applied displacements at node 6 are u=0.57 in and v=0.45 in the directions indicated. Calculate the stress in clement O, indicate tension (T) or compression (C).

The truss to the right is comprised of members with cross sectional area A = 3 in', length of 12 inches, and Young's Modulus E = 30x10 psi. The applied displacements at node 6 are u=0.57 in and v=0.45 in the directions indicated. Calculate the stress in clement O, indicate tension (T) or compression (C).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.1P: A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned...

See similar textbooks

Similar questions

A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Because of foundation settlement, a circular tower is leaning at an angle a to the vertical (see figure). The structural core of the tower is a circular cylinder of height ft, outer diameter d2, and inner diameter d1.For simplicity in the analysis, assume that the weight of the tower is uniformly distributed along the height. Obtain a formula for the maximum permissible angle a if there is to be no tensile stress in the tower.
The axial assembly consists of a solid 1-in.-diameter aluminum alloy [E = 11000 ksi, v = 0.26, α= 10.5 × 10−6/°F] rod (1) and a solid 1.49-in.-diameter bronze [E = 15300 ksi, v = 0.15, α= 7.6 × 10–6/°F] rod (2). Assume L1=11 in., L2=22 in. If the supports at A and C are rigid and the assembly is stress free at 16°F, determine:(a) the normal stresses σ1, σ2 in both rods at 213°F (positive if tensile, negative if compressive).(b) the displacement uB of flange B (positive if to the right, negative to the left).(c) the change in diameter Δd1 of the aluminum rod.
A unique column has been created with the geometry shown below, where the radius is r = (0.6e-0.08y2) m, the variable y is in meters. The column density of the column material is ρ = 3.21 Mg/m3. Determine the average normal stress at the bottom of the column (y = 0) in units of Pa.
The circular column is subjected to a compressive force of 5kN if the stress in the column is limitedto 17.63MPa, what is the limiting value of diameter d?
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips.Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
The prismatic bar has a circular cross section with 100-mm diameter. In a test to determine its elastic properties, the bar is subjected to 4.8-MN (meganewton) axial loads. In terms of the coordinate system shown, what are the six components of the state of stress at a point of the bar that is not near the ends where the forces are applied?
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..
A central horizontal section of a hook is a symmetrical trapezium of inner width=67.5mm and of outer width =22.5mm. The depth of the section is 90mm. The hookcarries a load of 37.5kN. The load line passes through the centre of curvature. Theradius of the hook is 52.5mm. Determine the maximum compressive and tensilestresses in the section of the hook.