When mixing 0.50 mL of 0.090 M bleach with 9.5 mL of 3.5 x 105 M yellow dye, what would be the following concentrations: (Express all answers to two significant figures.) a) Initial concentration of bleach after mixing but before reaction starts, in units of M. b) Initial concentration of yellow dye after mixing but before reaction starts, in units of M. c) Assuming the reaction goes to completion and the final concentration of dye goes to zero, what would be the final concentration of the bleach after the reaction, in units of M?

When mixing 0.50 mL of 0.090 M bleach with 9.5 mL of 3.5 x 105 M yellow dye, what would be the following concentrations: (Express all answers to two significant figures.) a) Initial concentration of bleach after mixing but before reaction starts, in units of M. b) Initial concentration of yellow dye after mixing but before reaction starts, in units of M. c) Assuming the reaction goes to completion and the final concentration of dye goes to zero, what would be the final concentration of the bleach after the reaction, in units of M?

Chemistry

9th Edition

ISBN:9781133611097

Author:Steven S. Zumdahl

Publisher:Steven S. Zumdahl

Chapter4: Types Of Chemical Reactions And Solution Stoichiometry

Section: Chapter Questions

Problem 122CP: In the spectroscopic analysis of many substances, a series of standard solutions of known...

See similar textbooks

Similar questions

On Easter Sunday, April 3, 1983, nitric acid spilled from a tank car near downtown Denver, Colorado. The spill was neutralized with sodium carbonate: 2HNO3(aq)+Na2CO3(aq)2NaNO3(aq)+H2O(l)+CO2(g) a. Calculate H for this reaction. Approximately 2.0 104 gal nitric acid was spilled. Assume that the acid was an aqueous solution containing 70.0% HNO3 by mass with a density of 1.42 glcm3. What mass of sodium carbonate was required for complete neutralization of the spill, and what quantity of heat was evolved? (Hf for NaNO3(aq) = 467 kJ/mol) b. According to The Denver Post for April 4, 1983, authorities feared that dangerous air pollution might occur during the neutralization. Considering the magnitude of H, what was their major concern?
A student weighs out a 4.80-g sample of aluminum bromide, transfers it to a 100-mL volumetric flask, adds enough water to dissolve it, and then adds water to the 100-mL mark. What is the molarity of aluminum bromide in the resulting solution?
The units of parts per million (ppm) and parts per billion (ppb) are commonly used by environmental chemists. In general, 1 ppm means 1 part of solute for every 106 parts of solution. Mathematically, by mass: ppm=gsolutegsolution=mgsolutekgsolution In the case of very dilute aqueous solutions, a concentration of 1.0 ppm is equal to 1.0 g of solute per 1.0 mL, which equals 1.0 g solution. Parts per billion is defined in a similar fashion. Calculate the molarity of each of the following aqueous solutions. a. 5.0 ppb Hg in H2O b. 1.0 ppb CHCl3 in H2O c. 10.0 ppm As in H2O d. 0.10 ppm DDT (C14H9Cl5) in H2O
What is the difference between a solute and a solvent?
Molarity is a conversion factor relating moles of solute in solution to the volume of the solution. How does one use molarity as a conversion factor to convert from moles of solute to volume of solution, and from volume of solution to moles of solute present?
You wish to prepare 1 L of a 0.02-M potassium iodate solution. You require that the final concentration be within 1% of 0.02 M and that the concentration must be known accurately to the fourth decimal place. How would you prepare this solution? Specify the glassware you would use, the accuracy needed for the balance, and the ranges of acceptable masses of KIO3 that can be used.
In the spectroscopic analysis of many substances, a series of standard solutions of known concentration are measured to generate a calibration curve. How would you prepare standard solutions containing 10.0, 25.0, 50.0, 75.0, and 100. ppm of copper from a commercially produced 1000.0-ppm solution? Assume each solution has a final volume of 100.0 mL. (See Exercise 123 for definitions.)
Apply Students conducted a lab to investigate limiting and excess reactants. The students added different volumes of sodium phosphate solution (Na3PO4) to a beaker. They then added a constant volume of cobalt(ll) nitrate solution (CO(NO3)2) stirred the contents, and allowed the beakers to sit overnight. The next day, each beaker had a purple precipitate at the bottom. The students decanted the supernatant from each beaker, divided it into two samples, and added one drop Of sodium phosphate solution to one sample and one drop of cobalt(ll) nitrate solution to the second sample. Their results are shown in Table 11.5. a. Write a balanced chemical equation for the reaction. b. Based on the results, identify the limiting reactant and the excess reactant for each trial.
A student was given a 1.6240-g sample of a mixture of sodium nitrate and sodium chloride and was asked to find the percentage of each compound in the mixture. She dissolved the sample and added a solution that contained an excess of silver nitrate. The silver ion precipitated all of the chloride ion in the mixture as silver chloride. It was filtered, dried, and weighed. Its mass was 2.056g. What was the percentage of each compound in the mixture?
ssume a highly magnified view of a solution of HCI that allows you to “see” the HCl. Draw this magnified view. If you dropped in a piece of magnesium, the magnesium would disappear, and hydrogen gas would he released. Represent this change using symbols for the elements, and write the balanced equation.
It is stated in Section 6.3 of the text that to balance equations by inspection you start “with the most complicated molecule.” What does this mean? Why is it best to do this?