When the natural drive energy of the reservoir is not strong enough to push the oil to the surface, artificial lift is employed to recover more production. ESP  is basically  suited  for  a.Low  volumes  of  well fluids b.Sand  laden  well  fluids c.High/large  volume  of well fluids

Q: Describe briefly the ways that knowledge of equal loudness contours can help you balance a mix.

A: When delivered with pure steady tones, an equal-loudness contour is a measure of sound pressure…

Q: Which statement is incorrect Select one: a. Diversity factor never will be less than unity b. Plant…

A: The diversity factor is always more than one, thus option a is correct. The statement b is also…

Q: With the neat diagram of the Gas turbine sketch all the internal parts of the typical gas turbine…

A: Schematic diagram of the Gas turbine:

Q: When the natural drive energy of the reservoir is not strong enough to push the oil to the surface,…

A:

Q: Describe the importance of planning before moving an item. SUBJECT INDUSTRIAL MAIN

A: All organizations whether it is the government, a private business or small businessman require…

Q: ind information about the details of “Slug Catcher” separator installed in Gas processing plants.…

A: Slug Catcher A Slug Catcher collects liquids in flow lines that can overburden the plant's…

Q: When deciding on the excavator-truck fleet, we should always select the option that ensure that the…

A: When deciding on the excavator-truck fleet, we should always select the option that ensure that the…

Q: Complete the diagram below by positioning labels into the correct position, identifying the main…

A: Solution:   The complete labelled diagram is given below:

Q: Petroleum production engineering is a subset of petroleum engineering. Petroleum production…

A: While producing the well the lowest pressures are observed near the wellbore. In oil reservoirs,…

Q: Crude based oil is an example of type of lubricant. Semi-solid O Liquid Gaseous Solid

A: Crude oil is a

Q: Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A: Crank and slotted lever mechanism:-

Q: s stoves, the recommended lubricant to be used in gas flow control valves is: No lubrication needed…

A: For gas stove, the lubricant is used in gas control valve as  Molybdenum disulfide or graphite…

Q: List any four factors that are to be considered in selection of storage tanks?

A: The factors are listed below:

Q: Multiple Evaporator Systems it may be required to

A: Solution-  Option C is correct, have different temp. Maintained at special zones.

Q: 7 - Which is not a type of freight car? A) safe

A: Option (e) is correct. high edged is not a type of freight car.

Q: Which of the following is capable of excavating to great depths but lacks positive digging action…

A: Answer is Clamshell

Q: What is the difference between a long position and a short position?

A: Long Position If an investor has long positions, it means that the investor has bought and owns…

Q: Identify an enginecring problem and apply principles of engineering economy to find the solution.

A: Principle of Engineering economy: Engineering economy is the science of applying economic criteria…

Q: Acidizing removes damage near wellbore by injecting fluid into the formation above the fracturing…

A: Option b is correct  True

Q: Project 2: In company that designs road cars and heavy trucks, it important to make the proper…

A: Hi, thank youy for the question! Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Isothermal process is the best for production of maximum work for all working fluids. False True

A: As we know there are various thermodynamic processes such as isobaric process, isochoric process,…

Q: 1. Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A:

Q: Gas turbines may be modified to be used for propulsion usage as for turbo jet-engine and…

A: The turbojet engine is used mainly in aircraft  Working principle of the turbojet engine In turbojet…

Q: 2- A gear pump with a rotational

A: Gear Pump: A gear pump pumps fluid through displacement, and it does so by the meshing of gears.…

Q: Briefly discuss, how the energy consumptions for operations of a fork lifter could be justified.

A: On average, one forklift consumed 65 L of diesel fuel per day, 7 L per hour, 1.6 L per load, 0.7 L…

Q: 3- List two reason, to keep low pressure drop across the production system.

A: Pressure drop is used to characterize the reduction in air pressure from the compressor discharge to…

Q: Give a situation where Lock-Out Tag-Out (LOTO) is needed. Why is it important?

A: LOTO (Lock Out Tag Out)  LOTO is a technical term basically used to  physical restraint of all…

Q: dentify any one application and draw a neat diagram for compressed air distribution system.

A: Application- Power generation, mining , computer industry, Pharmaceuticals.

Q: 16)In which process Catcher is used

A: Catcher is used in abrasive water jet machining According to question option c is absolutely correct

Q: Sir, you need to explain the process for the production.

A: In the given drawing, to make the same profile of the workpiece, Firstly we have to take a circular…

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: covergent-divergent

A: po=101kPaT0=30oC We have normal shock at exit which is case 6 it having supersonic at e1 and…

Q: To mention some types of engine lathes such as : Standard engine,Manufacturing engine,Bench lathers…

A: Option c is correct

Q: 17- Where does liquid ammonia change into its low pressure vapors

A:

Q: Dons at C, ar 2"

A:

Q: Which statement about hydroelectric power plant is wrong? Select one: O a. Its construction coast is…

A: Let us discuss all the options   (a) Its construction cost is very high and takes a long time for…

Q: 26. In this intake process, there is no intake pressure boost system. Intake of air and fuel is only…

A: The correct option is Vaccum charged, option (a).

Q: what is the packaging materials, by product, waste, and common utilities used in distillery plant of…

A:

Q: When the plant rotating equipment is installed what are possible environment problems will be faced…

A:

Q: FLAKABLE LIQUID 3. One precaution that needs to be foliowed in a work area displaying the sign shown…

A: Given Data⇒ Flammable liquid 3 Problem statement⇒ Problem says choose the correct option that what…

Q: 1.1 List five different ways in which the pumping of fluids can be accomplished.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: what the functions of well head in brief and Explain the functions???

A: Image of a wellhead:

Q: List any four factors that are to be considered in selection of storage tanks?

A: Given: Storage stank selection To find:- Factors for selection

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.