Which of the following indicates the correct rms value of the diode current for a 1-o full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 20 2 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (c) 4.95 A (d) 11 A

Which of the following indicates the correct rms value of the diode current for a 1-o full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 20 2 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (c) 4.95 A (d) 11 A

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
Which of the following indicates the correct rms value of the diode current for a 1-0 full bridge diode rectifier supplied by a source voltage of 220 V, 60 Hz? The value of load resistance is 2012 (assuming large inductance for maintain constant load current). (a) 9.90 A (b) 7.0 A (C) 4.95 A (d) 11 A COMPANY
E.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. F.) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. G.) For the circuit in Question (F) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage drop.
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
A number of diodes rated at 1620 V each are to be connected in series in a rectifier circuit with a maximum voltage of 3000V. A de-rating factor of 15% is recommended. The maximum difference in leakage current of the diodes is given as 10mA , and the maximum difference in stored charge is 20µC. Calculate, 1) the number of diodes that must be used, 2) a suitable component value for the static equalization circuit; 3) a suitable component value for the dynamic equalization circuit.
Question 5. A pure resistive R ohm resistor is connected to the output of the three-phase Bridge Rectifier and it provides 400 DC output voltage, 20A load current, and the source frequency is 50 Hertz.According to this(a) Yield(b) FF Coefficient,RF Coefficient,TU Value(c) Find the Reverse Peak Voltage (PIV) of each diode, the maximum value of the current flowing through the diode.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
Silicon Controlled Rectifier: Given that the input voltage is 100 V peak to peak, and firing angle of SCR is 30 degrees. Solve for the following: a. Average voltage of SCR b. Average voltage of the Diode c. Average current flowing from SCR d. RMS current flowing from the diode e. Total average voltage f. RMS voltage of SCR g. RMS voltage of the diode h. Total RMS voltage of the circuit
A single phase diode bridge rectifier has an input voltage of 240V and supplies a resistive load with a constant dc current of 10A. (a) Sketch a well labeled circuit of the rectifier described above.(b) Sketch the waveforms for the input voltage, output voltage, input current and output current. (c) Determine the maximum input voltage. (d) Load resistance. (e) Derive an equation for the average output voltage and calculate its value. (f) Derive an equation for the RMS value of the output voltage and calculate its value. (g) Determine the power dissipated in the load