Which of the following is not true about the preparations made for marine diesel propulsion engines before starting maneuvering? OA The main air starting valve should be opened to get ready for admission of starting air into the cylinders. OB. A heater is used to increase jacket cooling water temperature to eliminate the effects of cold starting the engine. OC Scavenge air valves should be opened to allow the scavenge air into the cylinders. OD. Turning gear should be operated to lubricate the cylinders if the engine is stopped for more than 30 minutes. OE. The engine should be tested for starting with the indicator cocks open to see if any abnormalities exist in-cylinder conditions.

Which of the following is not true about the preparations made for marine diesel propulsion engines before starting maneuvering? OA The main air starting valve should be opened to get ready for admission of starting air into the cylinders. OB. A heater is used to increase jacket cooling water temperature to eliminate the effects of cold starting the engine. OC Scavenge air valves should be opened to allow the scavenge air into the cylinders. OD. Turning gear should be operated to lubricate the cylinders if the engine is stopped for more than 30 minutes. OE. The engine should be tested for starting with the indicator cocks open to see if any abnormalities exist in-cylinder conditions.

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter12: Upper End Theory And Service

Section: Chapter Questions

Problem 7RQ: To allow the engine to run on the Atkinson cycle, Toyotas VVT-i system causes the- intake valve to...

See similar textbooks

Similar questions

Completely answer. Write legibly. 1. What are the most commonly used STARTING SYSTEM in Diesel Power Plant, Explain each type on how it is being used to start the Deisel Engine.2. What are the Environmental Impacts in the operation of a Barge Type Diesel Power Plant and its Mitigated Measures. Explain each Impact.
Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pump
Why must hydraulic line pressures increase when there is an increase of load on the engine?
Enumerate the advantages and disadvantages of the following types of engine: a.) Rotary or Wankle engine
Enumerate the advantages and disadvantages of the following types of engine: a) Four-stroke engineb) Two-stoke enginec) Rotary or Wankle engine
Discuss the main functions of the lubricating system of an engine
Which one is not true about the expansion tank in cooling water systems on marine diesel engines? ((It is a multiple choice marine diesel engine question, please specify the correct option.))
2- What is normal air flow rate? How is air flow pressure measured? 4- Which engine produces the most torque (diesel or petrol)? why? 5- Mention the air fuel ratio required by the engine during (a) Starting time zero load (b) Normal running half load (C)full load 6- Types of lubrication in an IC engine?
what are the two tune up methods used for a variety of big bore cummins engines
I need help on answering these from the following question below: 1. you need to calculate the mass flow rate of air inducted to the engine 2. from your answer, in the question above, you need to determine the ratios of heat release in the flue gas and cooling water against input power for the engine 3. you need to discuss how emissions can be minimised with regards to the engine The question: A diesel engine is a type of internal combustion engine that uses compression ignitio to turn energy in diesel fuel to rotary mechanical energy. A four-stroke (i = 0.5 for fourstroke engine, stroke = 150 mm and revolution = 2100 min−1) diesel engine with 6 cylinders and an effective specific fuel consumption of 0.23 kg kW−1h−1 has an effective and indicated mean pressure of 9.2 bar and 6.8 bar, respectively, and a compression ratio of 17. The ambient temperature and pressure of the diesel engine is 30 ℃ and 1.017 bar, respectively, and the temperature of the exhaust gas is 650 ℃. The clearance…
A six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC. Who is correct and explain why? Technician A Technician B Both A and B Neither A nor B
Answer the following question: 1. On an aircraft enumerate the turboprop starting procedures.