19.a. Which term relates to the conductors connected to the output side of a separately derived system? A. System conductor B. Derived phased conductor C. Transformer secondary conductor D. Neutral conductor 19.b. Overcurrent protection for a separately derived system must be located immediately adjacent to the A. disconnecting means. B. site-isolating device. C. grounded conductor. D. junction box

19.a. Which term relates to the conductors connected to the output side of a separately derived system? A. System conductor B. Derived phased conductor C. Transformer secondary conductor D. Neutral conductor 19.b. Overcurrent protection for a separately derived system must be located immediately adjacent to the A. disconnecting means. B. site-isolating device. C. grounded conductor. D. junction box

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter9: Lighting Branch Circuit For The Master Bedroom

Section: Chapter Questions

Problem 12R: a. Does the circuit for the Master Bedroom have a grounded circuit conductor? ____________________...

See similar textbooks

Similar questions

What type of bonding jumper connects the grounded circuit conductor and the equipment groundingconductor at the service?A. SystemB. Supply-sideC. MainD. Equipment
18. Which part of a lightning protection system is at the top of the structure?A. Ground terminal networkB. Down conductor networkC. Strike termination networkD. Equipotential bonding network
4.a. An intersystem bonding termination will typically be used as a ground junction for a/anA. patient care area.B. communications system installation.C. fire protection system.D. information technology room.4.b. The supply systems for sensitive electronic equipment are _______ systems.A. four-wire, three-phaseB. three-wire, single-phaseC. three-wire, three-phaseD. four-wire, single-phase
5. How many system bonding jumpers normally are there for a separately derived system that's grounded? A. ThreeB. TwoC. One D. Zero 6. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. ThreeB. TwoC. One D. Four 7. Which of the following are sometimes installed as an emergency system, legally required standby system, or optional standby power system for a building or structure? A. GeneratorsB. Surge protection devices C. Surge arrestersD. Transformers 8. If the system bonding jumper in a DC system is a screw, what color must the screw be? A. WhiteB. RedC. Orange D. Green 9. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct? A. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect. B. There's no need for service equipment or a panelboard in the separate building.C. A ground electrode must…
6. Which type of cable would you use to connect two buildings in an office installation?A. Buried loose-tube cableB. Aerial armored cableC. OFNP cableD. Tight-buffered cable
Which of the following is a term missing from the National Electrical Code but used by manufacturers of equipment that's suitable for use as service equipment? Micro-grid  Selective coordination Neutral disconnect link Grounding triad The _______ is required to be connected to the grounded conductor of the sensitive electronic system on the line side of the separately derived system disconnecting means. main bonding jumper  equipment grounding terminal bus neutral ground strap neutral disconnect link
D.1-. Which of the following names is commonly used for armored cable on commercial and industrial jobsites?A. RomexB. BXC. ECGD. MCD.2. Which of the following is the most common type of conductor termination used in commercial andindustrial wiring applications?A. A pressure connectionB. A wire nutC. A wire spliceD. A crimped connection D.3. Which of the following terms correctly describes a ventilated metal enclosure that supports powerdistribution conductors of up to 8000 A and 69 kV, and that allows for proper phase arrangement of theconductors?A. A trolley busB. A channel racewayC. A cablebusD. A feeder bus
List the methods by which an equipment grounding conductor is connected to a device box.
It is generally understood that grounding and bonding together all metal parts of an electrical system and the metal shield of the cable television cable to the same grounding reference point in a residence will keep both systems at the same voltage level should a surge, such as lightning, occur. Therefore, if the incoming cable that has been installed by the CATV cable company installer has the metal shield grounded to a driven ground rod, does this installation conform to the NEC? ___________
In the conduit diagram shown in attached picture, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect
3.Is it advisable to use Multi-pair punch in terminating cables in patch panels? Why?
How many 14 AWG THHN conductors, including an equipment grounding conductor, can be installed in a 3/8-in. flexible metal conduit using inside fittings? Select one: A. 2 B. 6 C. 4 D. 8