Plot the cycle points on a T-s diagramC. Calculate the specific power of the turbines (each separately.)d. Calculate the specific work of the pumps (each separately)E. Calculate the amount of specific heat evacuated in the condenser. P110Boiler1210P138200ClosedFWHIPIV14816T1335013ClosedFWH IIPIIIHigh-PTurbineOpenFWHPII10HP145200+[C]17Low-PTurbine18 mP153000PIр[кра]Reversible processes.• There is no pressure drop in the boiler and pipes.• The turbines are adiabatic (adiabatic + reversal =isentropic.)• The inlet temperatures to the turbines are thesame.• At the entrance to each pump, the water is in astate of saturated liquid.• In closed heat exchangers, the cooling water is atthe saturation temperature of the discharge water1911CondenserP16290P18110

P1 10 Boiler 12. P13 8200 PIV 14 16 Closed Closed FWHI FWHII 8 T13 350 13 PIII High-P Turbine Open FWH PII of P14 5200 T[C] 17 Low-P Turbine 18 m P15 3000 PI рекрај - Reversible processes. There is no pressure drop in the boiler and pipes. The turbines are adiabatic (adiabatic + reversal = sentropic.) The inlet temperatures to the turbines are the same. At the entrance to each pump, the water is in a state of saturated liquid. In closed heat exchangers, the cooling water is at of the dis Condenser P16 290 P18 110

P1 10 Boiler 12. P13 8200 PIV 14 16 Closed Closed FWHI FWHII 8 T13 350 13 PIII High-P Turbine Open FWH PII of P14 5200 T[C] 17 Low-P Turbine 18 m P15 3000 PI рекрај - Reversible processes. There is no pressure drop in the boiler and pipes. The turbines are adiabatic (adiabatic + reversal = sentropic.) The inlet temperatures to the turbines are the same. At the entrance to each pump, the water is in a state of saturated liquid. In closed heat exchangers, the cooling water is at of the dis Condenser P16 290 P18 110

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 20RQ: Welded ______sealed compressors are normally used in household refrigerators.

See similar textbooks

Similar questions

A heating plant for a large medical campus requires 5506 MBH (1MBH \= 1,000,000 btuh) of heating capacity. Which of the following pipe size and velocity in feet per second (fps) for the main would be needed if the plant is a 62 psig medium-pressure steam system? (Hint: Table 7.2) a.8" pipe at 130 fps b.4" pipe at 150 fps c.2" pipe at 100 fps d.4" pipe at 130 fps e.5506 MBH; 62 psig
Steam expands in a steam turbine isentropically from intet to exhaust having an enthalpy drop=1200 kJ/kg. Assuming ideal conditions determine the mean diameter of wheel if the turbine were of: (1) Single impulse stage. (i) Single 50% reabron stage.
Problem 1: The boiler of a power steam cycle operates at 6000 kPa and the condenser at 50 kPa. At the entrance to the turbine, the temperature is 500°C. The isentropic efficiency of the turbine is 90 percent, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 6.3°C. The boiler is sized for a mass flow rate of 18 kg/s. You are asked to: a. Represent the cycle on P-v and T-s diagrams. b. Compute the rate at which heat is added in the boiler. c. Compute the power required to operate the pumps. d. Determine the net power produced by the cycle. e. Compute the thermal efficiency.
Critically compare how heat transfer efficiency will affect the lifetime of the turbine.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
A single-acting, single-cylinder air compressor is rated at 4.25 m3/min of air. The suction conditions are 1 atm and 27 C and discharge pressure is 1034 kPa. The compression process follows the equation PV1.35 = A. Determine the power, in kW, required to compress the air. B.)what is the engine kW power needed to drive the unit if the combined engine-compressor efficiency is 84%? C.)if the compressor is to run two-stage at optimum intercooler pressure with perfect intercooling, what will be percentage of power saved?
IN ESSAY FORM: Explain and differentiate the concept and processes of Carnot cycle, Otto Cycle/Gasoline engine, Diesel Cycle, and Rankine Cycle
A trial run on a steam turbine power plant gave the following resultsEntrance to boiler Exit of turbineMass flow rate =3600 kg/h Velocity of steam=25 m/sEnthalpy of water=850 kJ/kg Elevation above datum=0Elevation above datum=4.3 m Enthalpy of steam=2625 kJ/kgVelocity of water=5 m/sDetermine the power developed by the turbine if the heat added in the boiler is 2100 kJ/s.
Design a steam power cycle that can achieve a cycle thermal efficiency of at least 40 percent under the conditions that all turbines have isentropic efficiencies of 83 percent and all pumps have isentropic efficiencies of 65 percent. please include (i) System figures and T-s diagrams with labelled states and temperature, pressure, enthalpy, and entropy information for your design. (ii) Sample calculations.
Explain and differentiate the concept and processes of Carnot cycle, Otto Cycle/Gasoline engine, Diesel Cycle, and Rankine Cycle
A R-12 compressor operates betwwen eveoperating temperature of 4 c ( hg = 353 kj/kg ), vg = 0.04895) and condensing temperature of 43 c ( hf = 241.6 kj/kg ).determine the bore diameter of the 4 cylinder 1000 rpm compressor if the piston speed is 200 meter/min and actual volumeter efficiency is 82% and refrigeration load is 25 tons
The thermal efficiency of the cycle.Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5%