With a volume of 200 L and a cylinder pressure of 100 kPa with the piston on the stopper a piston-cylinder assembly contains water with a degree of dryness of 50%. A pressure of 200 kPa is needed to move the piston up. Volume 400 The cylinder continues to be heated until it reaches According to this; a) This process takes into account the saturation line in the T-v and P-v diagram. show. b) Calculate the temperature in the final state. c) Find the work done. d) Find the amount of heat transfer.

With a volume of 200 L and a cylinder pressure of 100 kPa with the piston on the stopper a piston-cylinder assembly contains water with a degree of dryness of 50%. A pressure of 200 kPa is needed to move the piston up. Volume 400 The cylinder continues to be heated until it reaches According to this; a) This process takes into account the saturation line in the T-v and P-v diagram. show. b) Calculate the temperature in the final state. c) Find the work done. d) Find the amount of heat transfer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Does R410a as a refrigerant for cryogenic plant for liquid oxygen production recommendable? Explain the process in a PH diagram if it is.
In a piston-cylinder assembly, when the piston is on the stopper400 L and cylinder pressure 100 kPa and water with 20% drynessare available. 300 kPa pressure is needed to move the piston up.has. The cylinder continues to be heated until the volume is 800 L.According to this; a) This process takes into account the saturation lines in the T-v and P-v diagram show it by taking it. b) Calculate the temperature in the last case. c) Find the work done. d) Find the amount of heat transfer.
How much heat must be supplied to water at 180 degrees celcius to make 1 kg of wet steam at 9000 kpa , having a dryness fraction of 80% ?. I was given this as an answer ;but dont know where they found the enthalpy at a 180 degrees in steam table , and dont know how they got 163 for h1 at then end equation to calculate heat ? given; mass,m=1 kg temperature , t =180 degrees celcius pressure,p=9000kpa find q solution: from steam table at 180 degrees celcius , the enthalpy , hf=h10103 kj/kg from the steam table at 9000 kpa hf=763.22 hfg=1378.9 therefore : h2=hf + x (hfg) =763.22 +0.8(1378.9) =1866 kj/kg calculate heat required: q=h2-h1=1866-163=1703
Draw a VLLE diagram when the temperature is constant.
Calculate the work done by the gas during process. Express your answer in terms ofand .
SHOW THE TABLE USED! A fixed amount of carbon dioxide goes through a polytropic process where n=1.4. The initial temperature of the CO2 is 250 K. The final temperature of the CO, is 400 K. If the mass of the CO2 is 12 kg and behaves as an ideal gas, determine the work, the change in internal energy, and the heat transfer during the process (in kJ). Note that PV=mRT. In this problem, can the carbon dioxide be considered an ideal gas at the initial conditions if the initial pressure is 150 kPa? Justify your answer quantitatively.
A cylindrical tank 4 m long and 3 m diameter is used for oil storage. How many days can the tank supply the engine having 27°API with fuel consumption of 60 kg/hr?
At 5°F, the latent heat of vaporization (the heat needed to vaporize a liquid toa vapor) of R-124 is 70.7 Btu/lb. How many Btus of heat are needed tovaporize 18.6 pounds of R-124?
Steam with an enthalphy of 3015.2 Kj/kg undergoes a constant pressure at 1.0 MPa until the enthalphy becomes 2100 kj/kg. What are the d.) Work and e.) Heat
A closed rigid container has a volume of 1 m3 and holds air at 344.8 kPa and 273 K. Heat is added until the temperature is 6000K. (Rair = 0.287 kJ/kg K), (kair = 1.4). a. What is the mass of air?, b. What is the final pressure? , c. What is the change in enthalpy? and d. What is the value of heat added to the system? JUST ANSWER ONLY THE LETTER D.
So my chosen refrigerant is R-32. I'm having trouble finding a good range of pressure and temperature that takes the isentropic efficiency into account. I was using the software,EES, as my source of property retrieval since I couldn't find properties of R-32 anywhere else.
Pls solve accurate and fast A 1-kg steam-water mixture at 1.0 MPa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPa and the temperature to 400: Determine the heat added