Would the exponents, m and n, in your rate expression be larger than, smaller than, or unchanged from the correct values as a result of each of the following mistakes? Indicate clearly your reasoning. Experiment 3: 20.0mL of 0.10M KI, 5.0mL of distilled water, 5.0mL H2O2 rate = k[H2O2]m[I-]n a) A leak occurred around stopper A in the mouth of the Erlenmeyer flask during experiment 3.

Would the exponents, m and n, in your rate expression be larger than, smaller than, or unchanged from the correct values as a result of each of the following mistakes? Indicate clearly your reasoning. Experiment 3: 20.0mL of 0.10M KI, 5.0mL of distilled water, 5.0mL H2O2 rate = k[H2O2]m[I-]n a) A leak occurred around stopper A in the mouth of the Erlenmeyer flask during experiment 3.

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter11: Chemical Kinetics: Rates Of Reactions

Section11.3: Rate Law And Order Of Reactions

Problem 11.5PSP

See similar textbooks

Similar questions

Table 2: Molarity of H2O2 and KI and Reaction Rate Trial H2O2 Concentration, M KI Concentration, M Reaction Rate(Reciprocal Slope) 1 0.29 M 0.40 M 14.08 2 0.29 M 0.20M 25 3 0.023 M 0.40 M 20 Please help me with this part, and please show me all steps Order with respect to H2O2: Order with respect to KI:
Create an illustration showing the preparation of two-fold serial dilution follows the ratio of the final dilutions as shown in the table above.
Match Column A with Column B. Column A Column B ____1. Ionic Solid A. Expression to show relationship of rate of reaction with concentration of reactant ____2. Mole Fraction B. Diamond ____3. Network Covalent C. Ratio of partial moles to total moles ____4. Rate Expression D. NaCl ____5. Intermolecular Forces E. Mercury in a glass tube ____6. Dipole Moment F. Resistance of a liquid to flow ____7. H-bonding G. London Dispersion ____8.…
The following results were found after completion of Part C in the Experimental procedure: 0.056 M I- and 0.048 M H2O2 were used Run Catalyst Calculated Rate of Reaction (M/s) 1 none 0.031 2 10.00mL of 0.35 M FeCl2 0.52 Assuming the Rate Law = k[I-][H2O2] 2 Calculate the value of k for run 2. Give your answer to the nearest whole number.
Table 2: Molarity of H2O2 and KI and Reaction Rate Trial H2O2 Concentration, M KI Concentration, M Reaction Rate(Reciprocal Slope) 1 0.29 M 0.40 M 14.08 2 0.29 M 0.20M 25 3 0.023 M 0.40 M 20 help me with this part please, and show me all steps Order with respect to H2O2: Order with respect to KI:
I monitor the reaction of Compound B with a large excess of NaOH at 298 K, and get the following results for its absorbance over time: Time (seconds) Absorbance (no units) 0 0.4555 10 0.3857 20 0.3178 30 0.2457 40 0.2011 50 0.1798 60 0.1304 On the basis of these numbers and a spreadsheet program, answer the following question: What is the most-likely order of Compound B in its reaction with NaOH? a. 0 b. 4 c. 1 d. 3 e. 2
The concentration of hydrolyzed nitrocefin at each time point for an experiment is given below. Time (min) Concentration () 0.5 6.01 1 11.78 1.5 17.6 2 23.51 2.5 29.58 3 35.31 3.5 39.73 4 44.5 4.5 48.18 5 50.05 5.5 52.72 6 54.01 6.5 55.06 7 55.65 7.5 56.39 8 56.74 8.5 57.49 9 58.03 9.5 58.61 10 58.69 Make a graph that plots the concentration of hydrolyzed nitrocefin (in μM) against time (in seconds) using Excel, R, SPSS or other computable software. Where appropriate, include a trendline that shows the linear range on your graph. Include the equations for the trendlines and the R2 value on the graph. Your graph should also include a title and appropriate titles for the x- and y-axes, with units included where appropriate. To determine the initial velocity of a possible insert in this experiment, you must determine what the linear range is in these data. Based on your graph, which time points represent a suitable linear range?
Which experiment is NOT used as a method of physically measuring the reaction rate? Spectroscopy Conductivity Pressure measurements Titration
What is the rate of disapperance of A if the rate of consumption of A is 2.3 x 10^-3 m/s?
In this lab we will be expressing rate as a change in concentration of reactants over time. In order to calculate this we need to know the initial concentrations of our reagents after they are combined but before the reaction occurs. This is a dilution process. Recall that the calculation for a dilution is accomplished using the relationship M1V1 = M2V2. Complete the columns in table 3 for the initial concentrations of [I-] and [Fe3+]. As an example: For each trial the total volume, including the starch, is 100.25 mL. We will be using 0.0500 M KI and 0.0500 M Fe(NO3)3. For trial #1: [Fe3+] = (0.0100 L x 0.0500 mol/L) ÷ 0.10025 L = 0.00499 M Your answers for questions 1-6 should each have 3 sig figs. Questions 1-6 will ask you to calculate the initial concentration of either [I-] or [Fe3+] for each trial. You should then put the answers in table 3 on your lab report. What is the initial [I-] for trial #1? What is the initial [I-] for trial #2? What is the initial [I-] for trial…
What is the rate law expression for the reaction in sodium hydroxide and ethyl acetate? Trial NaOH CH3COOC2H5 Initial Condcutivity of NaOH Solution (uS/cm) Initial Rate (uS/cm)/s) 1 21 ml 2.1ml 1285 24.72 2 21 ml 2.1ml 2399 50.32 3 21 ml 2.1ml 1262 23.72
The line weaver Burk plot allows the relationship between reaction velocity and substrate concentration to be calculated as a ____________ instead of a hyperbola.