Write the thread notes for the following internal threads. Do only (b), (e) and (g). Also, what are the tap drill size and/or diameter and the pitch? use thread class = 3 (a) Major Ø Series (b) (c) (d) (e) 3/8 (f) (g) 7/16 1/4 5/8 1/2 1 Fine Coarse Fine Coarse Fine Extra Fine Coarse Thread Note Tap drill size and/or diameter Pitch Thread Note Tap drill size and/or diameter Pitch Thread Note Tap drill size and/or diameter Pitch

Write the thread notes for the following internal threads. Do only (b), (e) and (g). Also, what are the tap drill size and/or diameter and the pitch? use thread class = 3 (a) Major Ø Series (b) (c) (d) (e) 3/8 (f) (g) 7/16 1/4 5/8 1/2 1 Fine Coarse Fine Coarse Fine Extra Fine Coarse Thread Note Tap drill size and/or diameter Pitch Thread Note Tap drill size and/or diameter Pitch Thread Note Tap drill size and/or diameter Pitch

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Correction Ey = 500 × 10^-6
A winch drum has an effective diameter 0.25m and is turning at 22 rpm. What is the resulting line speed in m/min? Give your answer to 1 decimal place without units eg if you think it is 102.341m/min, simply type 102.3.
Two mating gears of 20 and 50 teeth of 20° pressure angle has path of contact equal to 35 mm What will be the arc of contact, (cos20 = 0.9397, tan 20°= 0.36397)
In an external thread the root diameter can be calculated by the following expression OD-2X depth mm 0.61X Pitch cm OD-2X depth cm 0.61X Pitch mm ------------ In a taper turning operation 30 is the diameter of the large end in mm, 20 is the taper angle in ° and 28 is the length of taper in mm. Find the diameter (d) of the small end in mm Diameter (d) of the small end in mm Answer
10. Measurement M = 3.495 inches at the gaging notch of a 3 inch pipe threads and the wire diameter is 0.07217 inch. Find the pitch diameter. (P = 0.125 inch)
The thread depth is measured along the ----------------- of the thread. Pitch Crest Angles Face
Consider a thread callout of Dia 0.375-10 UNF-2B. How far will the thread travel if it is subjected to 3 full rotations? (Assume infinite thread lengths for simplicity)? Units are in Inches List your answer in a decimal format.
Q-3 Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a = 40.500 0.025 mm b = 52.000 0.075 mm c = 73.000 0.015 mm d = 165.900 0.250 mm Parts A, B, and C are standard parts supplied by vendors from the market, but we are to machine part D according to the the width that you are asked to specify. (a) Determine the mean gap w0 of w and its tolerance. (b) Determine the mean size of d (d0) that will assure that w ≥ 0.050 mm.
21. What is the diameter of line shaft that transmit 180 kW at 25 rps?
Create a moody diagram of the following smooth and steel pipe:• Re= 100,456.85• ϵ/D= 0.001
Calculate the pitch diameter of a M10 × 1.5
When interested in performing a bending stress analysis for gear teeth, the width, F, should fall within this range related to diametral pitch Pd: a. F > 16/Pd b. F < 8/Pd c. 8/Pd < F