y = 3506.2x + 0.0421 R2 = 0.9978 A student prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. Using the standard curve above, if the absorbance for the solution was 0.422, calculate the equilibrium constant, Keq.

y = 3506.2x + 0.0421 R2 = 0.9978 A student prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. Using the standard curve above, if the absorbance for the solution was 0.422, calculate the equilibrium constant, Keq.

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section4.9: Spectrophotometry

Problem 4.14CYU

See similar textbooks

Similar questions

Calculate the molar absorptivity of a 1.00 x 10-4 M solution, which has an absorbance of 0.372, when the path length is 2.5 cm.
The absorbance of a solution containing 5.0 x 10^-3 g/L of a solute in a 1.00 m cell is 1.00. Calculate the absorptivity and the molar absorptivity if the molecular mass of the solute is 1.25.
Absorbance measurements were taken on a series of Fe standards complexed with 1,10-phenanthroline. A plot of absorbance vs. concentration yielded a linear curve with the equation y=1.008e03x + 0.0395 (where y is the absorbance and x represents the Fe concentration in moles/L). Using this information calculate the Fe concentration (in ppm) in a 40.0-mL aliquot of ground water that produced an absorbance of 0.580.
The nitrite in a series of standard solutions (mg/L, n = 5) are converted to azo dye and the slope of the calibration curve is 2.0 ppm1. A 10.00-mL mineral water sample is treated in the same way as standards and diluted to a final volume of 100.00-mL. It gives an absorbance of 0.80. The absorbance of blank solution under the same conditions is 0.10. Calculate ppm (mg/L) of NO2 (46 g/mol) and the molarity of NANO2 (69 g/mol) in the original sample
A 20 ml aliquot of drinking water containing Fe(II) and Fe (III) is treated with hydroquinone to reduce all dissolved iron to Fe(II),0- phenanthroline is added and the aliquot is diluted to 50 ml and the absorbance in a 2.00 cm cell is 0.085 at 510 nm. Calculate the iron content of the water as ppm? ε = 1.11 x 104 L/mol cm
The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate solutions of known concentration. You are asked to analyze a Fe(SCN)2+Fe(SCN)2+ solution with an unknown concentration and an absorbance value of 0.4150.415 . The slope-intercept form of the equation of the line is ?=4558.4?+0.0147y=4558.4⁢x+0.0147 . The unknown was analyzed on the same instrument as the standard curve solutions at the same temperature. What is the Fe3+Fe3+ concentration of the unknown solution?
Determine phosphate concentration of a water sample using the following information: Standard curve- slope: 1763.2 y-int: 0.011806 R^2: 0.99181 Absorbance of water sample: 0.013
Calculate the hardness in terms of parts per million calcium carbonate (100.0869 g/mol) in a 50.00 mL aliquot of milk sample. The sample was treated with a small amount of ammonia buffer to bring the pH to 10 followed by the addition of 10 drops EBT indicator. The milk sample required 10.00 mL of 8.000 x 10-3 M EDTA for titration. 160 ppm 4 80 320
If the absorbance for the solution was 0.544, calculate the equilibrium constant, Keq, with zero places after the decimal.
The concentration of glucose in an aqueous solution can be determined by oxidation with ferricyanide ion, Fe(CN)63–. The absorbance of the ferricyanide ion measured at 420 nm increases as the concentration of glucose increases. [Glucose], mg / mL Absorbance 0.005 0.132 0.010 0.290 0.020 0.498 0.030 0.642 0.040 0.750 Using the method of least-squares, give the equation of the best straight line through the points. Make sure that m=slope has 3 decimal places (XX.XXX) and y-intercept (b) has 2 significant figures (0.0XX). In your answer you should write in the form of y=mx+b. For instance, y = 12.316x + 0.072
Calculate the molar absorptivity of a solute when its measured absorbance is 1.050 with a concentration of 1.45 x 10-3 M. Assume the path length of the cell is 1.0 cm.
The concentration of yeast RNA in an aqueous solution is 12.0 mg/L. The absorbance is found to be 0.208 when this solution is placed in a 1.00 cm cell at 265 nm. Its molecular weight is 5.7 x 103 g/mol. a) Calculate the molar absorptivity of the yeast RNA. b) What will be the absorbance if the solution is 6.0 mg/L and the path length is 1.00 cm? c) What will be the absorbance if the solution is 12 mg/L and the path length is 2.00 cm? (Show your work)