You are a structural Engineer who works in Dar Al Handasah company. Your direct manager has called for a meeting and provided you with the below schematic design of a concrete beam that might be implemented at one of the sites. You were requested to calculate the following: ( make 15 KN bold) 40 KN 15 KN 20 KN 45 30 KN 40 KN m 16 20 Figure 1: Concrete Beam 1. Find the equivalent forces of the disturbed loads. 2. Sketch the beam showing all the applied forces (reaction and equivalent forces) and their suitable locations. 3. Apply the moment equations in the equilibrium state to find the value of the reaction forces at points A and B. 4. If the given beam in Figure 1 compressed to be 19.98 meter where the original tempreture was T1=200 K, find the temperature (T2) after the compression.

You are a structural Engineer who works in Dar Al Handasah company. Your direct manager has called for a meeting and provided you with the below schematic design of a concrete beam that might be implemented at one of the sites. You were requested to calculate the following: ( make 15 KN bold) 40 KN 15 KN 20 KN 45 30 KN 40 KN m 16 20 Figure 1: Concrete Beam 1. Find the equivalent forces of the disturbed loads. 2. Sketch the beam showing all the applied forces (reaction and equivalent forces) and their suitable locations. 3. Apply the moment equations in the equilibrium state to find the value of the reaction forces at points A and B. 4. If the given beam in Figure 1 compressed to be 19.98 meter where the original tempreture was T1=200 K, find the temperature (T2) after the compression.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.42P: For the beam AB shown in Cases 1 and 2, derive and plot expressions for the shear force and bending...

See similar textbooks

Similar questions

Floor joists are structural members which support flooring in structures, as in the diagram on the right. The floor sits upon the minor length of the joist, and the joists are set at equal spacing to reach the desired floor stiffness. How many 2x6 joists would it take to equal the floor stiffness of the same floor supported by ten (10) 2x12 joists of the same species?
In order to determine the magnitude of the internal forces, a FBD must be cut. It is difficult to determine where a cut should be made in order to reveal the Maximum Internal Forces, thus we have put the distance to the cut in terms of 'x', and plot the equation. In my lecture we took a generic portion of a Beam and applied equilibrium and saw that Loading, Shear and Moment are related to each through differential equations. Change in Shear is the Area under the Loading diagram. Change in Moment is the Area under the Shear Diagram. Using Graphic Integration draw the shear and moment diagrams for the given beams and loading.
SHOW YOUR SOLUTIONS PLS, INSTRUCTIONS: For the beam shown, (1) derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) (2) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Specify the values for key points on the diagrams. Let a=7.0 ft, b=8.7 ft, wa=13 kips/ft, and wb=7 kips/ft. QUESTIONS: 4) With reference to problem 1, what is the bending moment (in kip-ft rounded to the nearest whole number) at x = 9.0 ft? 5) With reference to problem 1, what is the maximum bending moment? Express your answer in kip-ft rounded to three significant figures.
P235 - The gate below is an isosceles triangle with 3m side. What is the proper configuration, the triangulate upright or inverted, so that the forces are as minimal as possible? - What would the forces be like in a circular 3m radius floodgate?
Hey, please reply as soon as posible Make the shear force and bending moment diagrams on Beam ABCDE. Also find the maximum values of shear force and bending moment (indicate the magnitudes of the maximum values and their location in the beam). You must justify the shape and values of the graphics you present. Consider that, in addition to the beam, there is a box with a "Weight" that is supported by the beam itself and the wall, by means of an arrangement of cables attached to the F ring. Consider the information provided on the reactions at points A and D. In the case of point A the only vertical reaction is supplied, directed downwards. important data: a = 285 m, b = 190 m, d= 380 m, e = 1995 m, f = 95 m, g = 190 m. Load in N/m, w=2,105 N/m. Weight: 200 NStrength: 50 NReaction force: D = 100 N, Ay = 50 N
A simply supported beam, 50mm wide by 100mm high and 300 mm long is subjected to a concentrated load of 3000 N at a point 100 mm from one of the supports. Draw the shear force and bending moment diagrams for the beam.
Solve using integration and please show graph: A horizontal beam 10 ft long has a variable load, zero at the leftmost end while 420lbf at the rightmost end. Calculate the total force felt by the beam.
Physics In a simple supported beam , write the moment equation of the beam shown in this video if it is loaded with 10 kN/m uniformly distributed over the entire simple span of 4 meters and a concentrated load of 20 kN applied 2 meters from the left support. Present your answer using the GAPSA form by indicating all the given data, what is being asked in the problem, the appropriate formula, the entire solutions / calculations and the answer accompanied with corresponding unit of measurement. Thank you.calculate the moment equation and the segment ,using double integration method
STRENGTH OF MATERIALS (Please write the complete solutions and FBDs completetely and correctly. No long explanation needed.Thumbs up will be given) A loaded beam, 60 mm wide by 200 mm high and 8 in long, has the shear and moment diagrams as shown below. (a) Determine the magnitude, type and location of the maximum flexural stress (b) Determine the type and magnitude of stress in a fiber 40 mm from the top of the beam at a section 2.5 m from the left end, Express final answers in MPa. (Use I=bh3/12
The cantilever beam in Fig. (a) carries a triangular load, the intensity of which varies from zero at the left end to 360 lb/ft at the right end. In addition, a 1000-lb upward vertical load acts at the free end of the beam. (1) Derive the shear force and bending moment equations, and (2) draw the shear force and bending moment diagrams. Neglect the weight of the beam
"Suppose someone with a body weight of 75 kg is lifting a box weighing 15 kg. If their back forms an angle of 70 degrees with the horizontal plane, and the distance from the object to the center of their body is 0.5 cm. The questions are as follows: 1. Create a free-body diagram for the above condition and apply the sign convention for forces and moments. 2. Calculate the magnitude of the compression force (F compression) and the shear force (F shear) generated. 3. Analyze whether this job is safe to perform."
Hey, please reply as soon as posible Static Problem Make the shear force and bending moment diagrams on ABCDE. Also find the maximum values of shear force and bending moment (indicate the magnitudes of the maximum values and their location in the beam). You must justify the shape and values of the graphics you present. Consider that, in addition to the beam, there is a box with a "Weight" that is supported by the beam itself and the wall, by means of an arrangement of cables attached to the F ring. Consider the information provided on the reactions at points A and D. In the case of point A the only vertical reaction is supplied, directed downwards. important data: a = 285 m, b = 190 m, d= 380 m, e = 1995 m, f = 95 m, g = 190 m. Load in N/m, w=2,105 N/m. Weight: 200 NStrength: 50 NReaction force: D = 100 N, Ay = 50 N