You are working as an engineer a company. During an energy audit, you realize that your company has a 40 kw transformer that is connected all the time. While inspecting the transformer, you calculate the core losses from the device to be approximately 5% of its rated capacity. Assume that the electrical costs are 10 C/kWh and 10 USD/KW/month of peak demand, that the average building use is 12 h/month, and that the average month has 720 hours. Estimate the annual cost savings from installing a switch that would energize the transformer only when the building was being used. The transformer is used h/month, and it can be turned off for the remaining of the month. That is h/month. That means the transformer can be turned off for h/year. The core losses from the tansformer is kW. Installing a switch to turn on the transformer only when the building is used results: Annual energy savings of kWh/year. Annual cost savings of USD/year. Does it make sense to use this strategy?

You are working as an engineer a company. During an energy audit, you realize that your company has a 40 kw transformer that is connected all the time. While inspecting the transformer, you calculate the core losses from the device to be approximately 5% of its rated capacity. Assume that the electrical costs are 10 C/kWh and 10 USD/KW/month of peak demand, that the average building use is 12 h/month, and that the average month has 720 hours. Estimate the annual cost savings from installing a switch that would energize the transformer only when the building was being used. The transformer is used h/month, and it can be turned off for the remaining of the month. That is h/month. That means the transformer can be turned off for h/year. The core losses from the tansformer is kW. Installing a switch to turn on the transformer only when the building is used results: Annual energy savings of kWh/year. Annual cost savings of USD/year. Does it make sense to use this strategy?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are given five light bulbs designed to operate on 160 mA current at 3.0 V (rms values), arid want to connect them in parallel, through an ideal transformer, to 120 V rms AC household power. a) Draw a circuit diagram showing the AC power source (a generator symbol ), the transformer, and resistors for the light bulbs. b) Is the required transformer step-up or step-down? What turns ratio N5/N is needed? e) Calculate the ruts current through both the primary and secondary coils of the trans former, in mA.
An ideal transformer is rated to deliver 460 kVA at380 V to a customer, as shown in Figure.a. How much current can the transformer supply tothe customer?b. If the customer’s load is purely resistive (i.e., ifpf = 1), what is the maximum power that thecustomer can receive?c. If the customer’s power factor is 0.8 (lagging),what is the maximum usable power the customercan receive?d. What is the maximum power if the pf is 0.7(lagging)?e. If the customer requires 300 kW to operate, what isthe minimum power factor with the given sizetransformer?
A 10 kVA, 500/250 V, single phase transformer has its maximum efficiency of 94% when delivering 90% of its rated output at unity p.t. Estimate its efficiency when delivering its full load output at p.t. of 0.8 lagging.3
A 2.4-kVA, 2400/240-V, 50-Hz, step-down transformer has the followingparameters: R, = 1.5 a, X, = 2.5 R, R, = 0.02 a, X, = 0.03 Q, R,, = 6 kR,and X,, = 8 kR. It is operating at 80% of its load at unity power factor.Using the exact equivalent circuit embodying the ideal transformer, determine the efficiency of the transformer. Also sketch its phasor diagram.
Neon signs (which often contain gases other than neon) use high voltage to excite gaseous atoms that then give off a characteristic glow. When plugged into a wall outlet (120 V AC), a typical neon sign transformer delivers 400 W AC at a voltage of 18 kV rms. The primary coil has 400 turns. 1. First, what is the number of turns in the secondary to achieve this high voltage? Give your answer to 2 significant digits. 2. Next, if the transformer is ideal, what is the rms current in the primary? Give you answer in amps with 2 significant digits. 3. Finally, what is the rms current in the secondary? Give your answer in milli-amps with 2 significant digits.
Demand factor is 0.75 on a Distributing Transformer that supplies a group of general power customers having a connected load of 186 kW. If the load factor for the group will average 45% and the energy sells at 3.5 cents per kWh, what will be the monthly (30-day) income from energy delivered through this transformer in Php/month; assuming an average motor efficiency to be 75%. (
A 10 kVA, 500/250 V, single phase transformer has its maximum efficiency of 94% when delivering 90% of its rated output at unity p.t. Estimate its efficiency when delivering its full load output at p.t. of 0.8 lagging,
????????????:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units???????:Calculate the all-day efficiency of a 100-KVA transformer operating under the following conditions:6 hour, 50 kW, 0.73 pf3 hours, 90 kW, 0.82 pfIron loss = 1000 wattsOne quarter load Copper loss = 66.25 wattsa) The rest of the day, transformer running idleb) The rest of the day, primary disconnected from the source.
Electrical Engineering - Power System Analysis Please solve the question quickly
A transformer with a primary of 1500 turns is used to generate 10V ac from A supply voltage of 120 V. How many turns are there on the secondary? If the secondary is loaded with 22 ohms resistor, What is the primary current? Please solve the problem, in the subject Industrial electronics. Thank you
A two-story house with a full basement has an outside dimension of 7.3 m (24 f) by 9.1 m (30 ft). Assuming three appliance circuits, determine the total load and the total demand load. Determine the wind power of a wind turbine travelling the speed of 36km/hr and has a blade length of 3000mm.
Electrical Engineering - Power System Analysis Please solve the question step by step