You have built the majority of the tension testing machine, but much of the instrumentation is still being assembled. To test the machine, you perform a test on a steel specimen with known properties. The machine provides you with the given load data, and you manually record the lengths between the marks on the specimen at each point using an extensometer to obtain the table of data shown below L (in) 2.2804 2.0012 3.51 2.0025 7,09 2.0350 7.87 20798 8.83 2.1313 9.84 2.1937 10.80 P (kip) 11.77 Use these results to calculate the stress and strain at the yield point, the ultimate strength point, and the fracture point Express your answers to three significant figures. View Available Hint(s) 14 12 10 stress= strain = ksi stress = ?? ksi 2.4774 12.37 D 2.5791 11.80 2.6657 10.81 2.7281 9.81 2.74 9

You have built the majority of the tension testing machine, but much of the instrumentation is still being assembled. To test the machine, you perform a test on a steel specimen with known properties. The machine provides you with the given load data, and you manually record the lengths between the marks on the specimen at each point using an extensometer to obtain the table of data shown below L (in) 2.2804 2.0012 3.51 2.0025 7,09 2.0350 7.87 20798 8.83 2.1313 9.84 2.1937 10.80 P (kip) 11.77 Use these results to calculate the stress and strain at the yield point, the ultimate strength point, and the fracture point Express your answers to three significant figures. View Available Hint(s) 14 12 10 stress= strain = ksi stress = ?? ksi 2.4774 12.37 D 2.5791 11.80 2.6657 10.81 2.7281 9.81 2.74 9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A) An engineer works for a company that has many gray cast iron rods of different diameters and would like to design an equivalent rod that could handle a force of P= 10.0 kipkip without fracturing. What is the minimum diameter that this new rod must have to support P? B)A tensile test is being conducted on a steel-rod specimen with a gauge length of L0 = 4.0 in and an initial diameter of d0 = 0.75 in. If the final length of the rod at fracture is Lf= 5.53 in , find the percent elongation of the rod at fracture.
"Using a 1-kg load at a specified joint, your experiment displayed that the bottom chord experienced a tensile force FBC of 2.1 N. If your computations showed that FBC is equal to 2.2 N (tensile), what is the percentage error?"
The following results were obtained in a tensile test on a mild steel specimen of original diameter 28 mm and gauge length 56 mm. Load at limit of proportionality : 96 kN Extension at 96 kN load : 0.068 mm Load at yield point : 105 kN Maximum load : 170 kN When the two parts were fitted together after being broken, the length between gauge length was found to be 65.8 mm and the diameter at the neck was 18.8 mm. Calculate: (a). E, (b).σy, (c).σu, (d). PRIA and PE
A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress–strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 0.001 mm/mm.
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph.
In a tensile test on a specimen of black mild steel of 12 mm diameter, the following results were obtained for a gauge length of 60 mm. Load W(kN) 5 10 15 20 25 30 35 40 Extension x (10-3 mm) 14 27.2 41 54 67.6 81.2 96 112 When tested to destruction. Maximum load = 65 kN; load at fracture = 50 kN, diameter at fracture = 7.5 mm, total extension on gauge length = 17 mm. Find young's modulus, specific modulus, ultimate tensile stress, breaking stress, true stress at fracture, limit of proportionality, percentage elongation, percentage reduction in area. The relative density of the steel is 7.8. Draw the straight line graph. Answer: breaking stress,true stress at fracture and limit of proportionality.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, of diameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine: (i) the stress, (ii) the strain, (iii) the modulus of elasticity. (b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, both measurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine: (i) the stress in the spacer, (ii) the compressive load on the spacer. rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer thisquestion fully? If you use * could you please explain what you mean by it! Thank You :)
Seatwork: Show your complete solution. Use 4 decimal places. Poisson’s Ratio: A square bar of aluminum 40 mm on a side and 220 mm long is loaded by axial tensile forces at the ends. Experimentally, it is found that the strain in the direction of the load is 0.001. Determine the volume of the bar when the load is acting. Considering a Poisson’s ratio of 0.33
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test. A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50 mm and initial diameter of d0=13 mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 506 MPa , e = 689 MPa , g = 585 MPa , and h = 0.146 mm/mm . A) Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 53.0 mm . B) Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 16.0 kN , find the nominal stress experienced by the rod. C)Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
A square bar subjected to a tensile load of 100kN having a gauge length of 200mm extends to a length of 0.19mm . Given the tensile strength as 200 MPa , determine ( 1 ) Side of the bar ( express in mm ) Final length ( express in mm ) Modulus of elasticity ( express )
38)A tensile test specimen has a gage length=3.0 inches and a diameter= .75 inches. Yielding occurs at a load of 38000lbs. The corresponding gage length=3.0103 inches (neglect the .0.2% yield point). The maximum load of 54000lbs i9s reached at a gage length =3.453 inches. Determine the tensile strength (Round to the nearest whole ksi)
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?