Your firm needs a computerized machine tool lathe which costs $50,000 and requires $12,000 in maintenance for each year of its 3-year life. After three years, this machine will be replaced. The machine falls into the MACRS 3-year class life category, and neither bonus depreciation nor Section 179 expensing can be used. Assume a tax rate of 21 percent and a discount rate of 12 percent. Calculate the depreciation tax shield for this project in year 3. (Round your answer to 2 decimal places.) Depreciation tax shield

Your firm needs a computerized machine tool lathe which costs $50,000 and requires $12,000 in maintenance for each year of its 3-year life. After three years, this machine will be replaced. The machine falls into the MACRS 3-year class life category, and neither bonus depreciation nor Section 179 expensing can be used. Assume a tax rate of 21 percent and a discount rate of 12 percent. Calculate the depreciation tax shield for this project in year 3. (Round your answer to 2 decimal places.) Depreciation tax shield

Corporate Fin Focused Approach

5th Edition

ISBN:9781285660516

Author:EHRHARDT

Publisher:EHRHARDT

Chapter11: Cash Flow Estimation And Risk Analysis

Section: Chapter Questions

Problem 5P

See similar textbooks

Similar questions

Dauten is offered a replacement machine which has a cost of 8,000, an estimated useful life of 6 years, and an estimated salvage value of 800. The replacement machine is eligible for 100% bonus depreciation at the time of purchase- The replacement machine would permit an output expansion, so sales would rise by 1,000 per year; even so, the new machines much greater efficiency would cause operating expenses to decline by 1,500 per year The new machine would require that inventories be increased by 2,000, but accounts payable would simultaneously increase by 500. Dautens marginal federal-plus-state tax rate is 25%, and its WACC is 11%. Should it replace the old machine?
The Scampini Supplies Company recently purchased a new delivery truck. The new truck cost $22,500, and it is expected to generate net after-tax operating cash flows, including depreciation, of $6,250 per year. The truck has a 5-year expected life. The expected salvage values after tax adjustments for the truck are given here. The company’s cost of capital is 10%. Should the firm operate the truck until the end of its 5-year physical life? If not, then what is its optimal economic life? Would the introduction of salvage values, in addition to operating cash flows, ever reduce the expected NPV and/or IRR of a project?
Filkins Fabric Company is considering the replacement of its old, fully depreciated knitting machine. Two new models are available: Machine 190-3, which has a cost of $190,000, a 3-year expected life, and after-tax cash flows (labor savings and depreciation) of $87,000 per year; and Machine 360-6, which has a cost of $360,000, a 6-year life, and after-tax cash flows of $98,300 per year. Knitting machine prices are not expected to rise because inflation will be offset by cheaper components (microprocessors) used in the machines. Assume that Filkins’ cost of capital is 14%. Should the firm replace its old knitting machine? If so, which new machine should it use? By how much would the value of the company increase if it accepted the better machine? What is the equivalent annual annuity for each machine?
Wendys boss wants to use straight-line depreciation for the new expansion project because he said it will give higher net income in earlier years and give him a larger bonus. The project will last 4 years and requires 1,700,000 of equipment. The company could use either straight line or the 3-year MACRS accelerated method. Under straight-line depreciation, the cost of the equipment would be depreciated evenly over its 4-year life. (Ignore the half-year convention for the straight-line method.) The applicable MACRS depreciation rates are 33.33%, 44.45%, 14.81%, and 7.41%, as discussed in Appendix 11A. The project cost of capital is 10%, and its tax rate is 25%. a. What would the depreciation expense be each year under each method? b. Which depreciation method would produce the higher NPV, and how much higher would it be? c. Why might Wendys boss prefer straight-line depreciation?