Your virtualization server uses vSphere from VMware. You have created several VMs for which you must provide network connectivity. After you create a virtual switch, you edit the settings of one of the VMs to attach it to the switch, but you are unable to do so. What should you do to so you can attach the VMs to the new virtual switch? a. create a port group b. configure TCP/IP c. enable the virtual switch

Your virtualization server uses vSphere from VMware. You have created several VMs for which you must provide network connectivity. After you create a virtual switch, you edit the settings of one of the VMs to attach it to the switch, but you are unable to do so. What should you do to so you can attach the VMs to the new virtual switch? a. create a port group b. configure TCP/IP c. enable the virtual switch

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter7: Setting Up A Local Network

Section: Chapter Questions

Problem 5TC

See similar textbooks

Similar questions

You as a network administrator want to protect the network from unauthorized traffic, and for this reason, you decide to change the native VLAN to an unused VLAN so that the untagged traffic is essentially directed toward a dead-end. Which of the following commands will you use to do this on a Cisco switch? a. set native-vlan-id b. set port-mode trunk c. switchport trunk native vlan d. ip dhcp snooping
Arriving at your university room, you plug into the wired Ethernet jack for the first time. The network admin has a record of your MAC address and your machine can join the network without further action on your part. Assume: Your laptop's Ethernet address is 0a:0b:0c:0d:0e:0f, DHCP server address is 131.111.7.3, your IPv4 address will be 131.111.7.121, the gateway's IP address is 131.111.7.1, and Ethernet address is 00:01:02:03:04:05, the network subnet mask is 255.255.255.0.Write the series of protocol/packet exchanges that occur on the wired Ethernet link, up until you can send a single packet to 128.232.0.20. You do not need to describe packets after this packet has left the link. Include ARP and DHCP
Your Network Administrator has contacted you to assist in examining a workstation that has been showing network fluctuations time and again. It seems that someone spilled some hot water over the Ethernet ports. Which of the following addresses will you choose to check the functionality of the Ethernet card without worrying about corrupted hardware and to ensure that the workstation's TCP/IP services are running? ping -a 8.8.8.8 ping -a 0.0.0.0 ping 127.0.0.1 ping 192.168.1.1
You have administrative responsibility for StormWind Studios. IP Address Management is currently being installed and set up. After setting up your IP address management server, the following step is to set up the group policy objects (GPOs) that will be used for IP address management provisioning. To ensure IPAM runs well, which PowerShell command is responsible for creating the required Provisioned GPOs?
Your network has a device with an Ethernet NIC that is set up with a static IPv4 address. Which two of the following IPv4 settings will be shown in the PC's IPv4 configuration? Traceroute address server DHCP Server address IP address of the PC DNS server address
Q5) The network administrator decided to deny traffic from PC1to PC4 while permitting it from PCO and PC2 to PC4. However, by testing the ACL configuration on R2, the network administrator has discovered that all hosts in the 10.0.1.0/24 network are not ABLE to communicate with PC4. interface Gigabitéthernet 0/0 ipaddress 10.0.3.1255.255.255.0 no shut down ip access-group 115 OUT R28sh access-lists StandardIP access list1ls 10 deny 10.0.1.0 0.0.0.255 20 permit any 1) Is the ACL number convenient for the stated policy? * (O No: for standard between 1and 99 (O No: for standard between 150 and 199 (O Yes: for standard > 99
Ross is running a small data entry back office, for which he has contracted you for network management. Ross has made it very clear that because he has just started the company he wants to cut down on expenses wherever he can. One such option involves the router-he wants to exchange the router with a similar but less expensive alternative. Which of the following will you refer to Ross in such a situation? a. A layer 3 switch b. An SDN controller c. Storm control d. A root port Which of the following is a distinct network of storage devices that communicate directly with each other and with other portions of the network? a. SDN b. A BPDU guard c. STP d. A SAN
Your computer is configured to obtain an IPv4 address and DNS server address automatically. Which utility will help you to find the IPv4 address of your computer? (Choose all that apply.)
q30- A PC cannot connect to any remote websites ping its default gateway, or ping a printer that is functioning properly on the local network segment. Which action will verify that the TCP/IP stack is functioning correctly on this PC? Select one: A. Download a troubleshooting tool from the PC manufacturer's website B. Use the traceroute command at the command prompt to identify any failures on the path to the gateway C. Use the ping 127.0.0.1 command at the command prompt D. Use the ipconfig /all command at the hosts command prompt E. Use FTP to check for connectivity to remote sites
Your DHCP server's configuration has been updated to include these new DNS servers. As a whole, what is the best way for your clients to get the new settings? * Perform a double restart of the computer. Enter ipconfig /registerDNS on the client. DHCP clients must wait for the lease to be renewed before continuing to use the network. O Input ipconfig /renew into the client's terminal. Clear the server's DNS cache.
A device on your network has an Ethernet NIC with a static IPv4 configuration. Which two of the following IPv4 parameters will be listed in the PC's IPv4 configuration? Traceroute server hostname DHCP Server address PC's private IP address DNS server address
Loss of network connectivity can be frustrating to users and can be costly to a business. As an IT technician, you might be asked to restore these connections. Familiarity with TCP/IP utilities can help you narrow down the source of the problem. Open a command prompt, type ipconfig /all and press enter 1. What is the IP address? 2. What is the physical address (MAC)? 3. What is the address of the default gateway? 4. What is the address of the DHCP server? 5. What is the address of the DNS server? Type ping cengage.com and press enter. 6. What is the IP address that was pinged? 7. Where did that IP address come from? Type nslookup course.com. 8. What is the IP address returned? Open a browswer and go to sctech.edu. At the command prompt type ipconfig /displaydns and press enter. Browse through the results. 9. What is the IP address for sctech.edu?