Cable BB PROBLEM 1.4-8

Q: 1. A wall-mounted jib crane is shown in the Figure below. Overall dimensions of the crane are a =…

A:

Q: An 18" depth beam is bolted to a 24" depth girder is connected similar to that in figure shown…

A:

Q: In the assembly of the bronze tube and steel bolt shown in the figure, the pitch of the bolt thread…

A: GIVEN DATA -

Q: 5. A rigid bar AB of length L = 66 in. is hinged to a support at A and supported by two vertical…

A:

Q: Q2/ The rigid platform in Figure below has negligible mass and rests on two steel bars, each 250 mm…

A:

Q: Q: A rigid block of negligible mass is supported by three rods as shown in figure, if a load (P) is…

A:

Q: A homogenous rigid block subjected to the loading shown in figure is supported by three steel rod…

A: Given: Diameter of steel rod, d=25 mm

Q: An angle bracket having a thickness t=0.75 in. is attached to the flange of a column by two 5/8-inch…

A: Given data, Thickness of the bracket, t = 0.75 in Diameter of the bolt, db = 0.625 in Pressure on…

Q: A circular post, a rectangular post, and a post of cruciform cross section are each compressed by…

A: Given: Diameter and the depth of rectangular and cruciform post=d Load acting at corner of the each…

Q: The cable shown "in the figure camies a TOPIC: INTERNAL STRESSES OF MEMBER AND CABLES 8.CablesT NO.…

A:

Q: 0.4 m y 0.2 m 0.3 m 0.6 m 5 m EFG kirişinin enine kesiti В 0.25 m 1200 N Q2) As shown in the figure,…

A: Given: The width of the cross-section, b = 25 mm The height of the cross-section, h = 50 mm The…

Q: A gondola on a ski lift is supported by two bent arms, as shown in the figure. Each arm is offset by…

A: Given: Weight of the gondola (W)=12kNDistance b=0.180mAllowable tensile stress (σy)=100MPaAllowable…

Q: The rigid horizontal bar AB is supported by three vertical wires as shown in the figure and carries…

A:

Q: The upper deck of a footballs stadium is supported by braces, each of which transfers a load P = 700…

A:

Q: A rod of weight 800kg is supported at the end using Steel and Bronze cable as shown in the figure…

A:

Q: 2.3-3 A steel bar AD (see figure) has a cross-sectional area of 0.40 in.² and is loaded by forces P,…

A:

Q: Two bars of rectangular cross section (thickness t=15 mm) are connected by a bolt in the manner…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: The figure below shown that the three bars are supported a rigid beam ACE. ar CD is made of steel…

A: Given data, d= diameter of each bar =10 mm σAl=allowable stress for aluminum=120 MPa σsteel=…

Q: Two flat bars loaded in tension by forces P are spliced using two rectangular splice plates and two…

A: The allowable value of load P is 6.14 kips.

Q: An angle bracket having a thickness t = 0.75 in. is attached to the flange of a column by two…

A: Given that , thickness (t)=0.75 in bracket width (b)=3 inbracket length (l) =8 in bracket pressure…

Q: Problem 3 The steel rod shown in the figure is stress- free before the axial loads P1 = 150 kN and…

A:

Q: The pinned joint shown in the figure below is held by a ¾-in-diameter pin at A. If the force P = 5…

A: Given data :- diameter= 3/4 in Force(P) =5kips Thickness =1 in

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?.…

A:

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm?.…

A: GivenAc=600mm2τAallowable=80MPa

Q: 1.2-10 A car having a mass of 5500 kg is pulled slowly up a steep inclined track by a steel cable…

A:

Q: A plane frame with pin supports at A and Ehas a cable attached at C, which runs over a…

A: a.Free body diagram:   No horizontal force on frame,henceEx=0Now,Ey+Ay=500lb⇒Ey=500lb-AyNow,Net…

Q: A 9 ft A = 0.5 in.2 12 ft C A = 16 in.?

A: Find the stresses in each member

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional…

A: Given:A1=175 mm2A2=300 mm2w=16 KN/mL=2.8 ma=1.7 m

Q: For the cantilever truss in Figure, determine the force in each member. | 100 N 60 30 5m 10 m 1000 N…

A: For  the given truss  To determine  forces in each member

Q: For the truss shown in Figure The cross sectional area of each member is 1000 mm² Find the stresses…

A:

Q: A thin-walled cylindrical pressure vessel of radius r is subjected simultaneously to internal gas…

A:

Q: While removing a wheel to change a tire, a driver applies forces P = 25 lb at the ends oftwo of the…

A: Stress : When a material is subjected to an external influence (Force, moment, Torque etc) a…

Q: For the structure shown in the figure, calculate the size of the bolt and area of the bear- 1-18.…

A:

Q: For the truss shown in Figure The cross sectional area of each member is 1000 mm? 3 m Find the…

A: For the given truss  Cross-sectional area (A) of each member =  1000 mm2 To determine  Stresses in…

Q: The upper deck of a football stadium is supportedby braces, each of which transfers a load P = 160…

A: Given:Load transfer to base of column=P=160kipsForce on each flange,Pf=160kips4=40 kipsThickness of…

Q: A reinforced concrete column 300 mm in diameter is designed to carry an axial compressive load, P =…

A: In this problem it contains compound column. When force acts on a column it gets elongate or…

Q: In the system in the figure, two rods carry the P force. a) Since the maximum stress that the rods…

A:

Q: A 3m x 3m x 76 mm thick precast slab is lifted by a crane by using cables on lift-up points provided…

A:

Q: The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional…

A: according the the given figure

Q: Q3 // Two 300 mm x 16 mm plates are riveted together with 25 mm diameter rivets double cover butt…

A: Given: Diameter of the each rivet: d= 25 mm Width of each plate, b = 300 mm and thickness of the…

Q: support reaction forces

A: Given: A plane frame with load 2P as shown in Fig To determine all support reaction Forces

Q: In the figure, member AB is used to support a load of 20kN at the free end, if the cable CD has a…

A: Answer:  tensile stress in the cable = 62.37 MPaFor a step-by-step solution have a look through the…

Q: The pins at B and D in the figure apply an axial load to diagonal bracing member BD. If BD has a…

A:

Q: Problem 1.6 The inclined ladder AB supports a house painter (82 kg) at C and the self weight (q = 36…

A: givenAB is a ladder weight of house painter at C W=82kgself weight of the ladder itself…

Q: A flat bar of rectangular cross section, length L, and constant thickness tis subjected to tension…

A:

Q: The flat bar shown in the figure is subjected to tensile forces P = 3000 lb. The bar has thickness t…

A: In the question, there is a fillet of some radius is given in the bar. Thus there will be a factor…

Q: A flat bar of width b= 60 mm and thickness t is loaded in tension by a force P (see figure). The bar…

A:

Q: uniform concrete slab of total weight W is to be attached, as shown in the figure, to two rods whose…

A: Dear student, we are suppose to solve only three sub parts. Please post other parts as a separate…

Q: Figure Problem In the figure shown, determine the stress in the cable C if its area is 600 mm².…

A: GivenAC=600mm2τaallowable=80MPa=80 N/mm2

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.