Answered: End B of the 60-lb homogeneous bar is…

End B of the 60-lb homogeneous bar is pulled by the 80-lb force inclined at 45° to the horizontal. Find θ, the angle of inclination of the bar.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.21P: The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed....

See similar textbooks

Related questions

Q: Please solve step by step. Thanks.

A: Elastic collision The collision between the two objects is said to be elastic collision if the colli...

Q: A steel tape is 30 m. long under a standard pull of 6 kg. with a constant cross-sectional area of 0....

A: Given data:

Q: part d please

A: First of all, make a FBD of the diagram as shown below,

Q: A machinist was tasked to insert an aluminum piston into a steel cylinder. The inside diameter of th...

A: Given data Da=0.4998 mDs=0.5 m

Q: At room temperature, what fraction of the nitrogen molecules in the air are moving at less than 300 ...

A: Probability of the speed of particles is given by the integral of the Maxwell distribution from 0 to...

Q: Etudier la continuité de la fonction f en 0 : x2 + 2|x| f(x) %3D X

Q: What will affect the heat transfer rate in heat exchangers?

A: Heat transfer rate in a heat exchanger are affected by a number of factors and they are as follows, ...

Q: VA VB В cC UBC Engineering A gear sits between two moving racks. If the top rack moves at a velocity...

A: Let assume that the velocity of rack A =VA = 0.75 msand velocity of rack B =VB= 0.45 msRadius of ...

Q: car is parked i. ii. The rear wheels of the car in Figure 2 is kept locked by the brakes whiles the ...

A: Given data: Weight of the car, W = 3300 lb. Part (a) Draw the free-body diagram for the upslope co...

Q: A 150 kg box is supported by a beam Z and cable K as shown in the figure below. Determine the forces...

A: Given data: Mass of the box, m = 150 kg. Draw the free-body diagram of the system, Apply Lami's t...

Q: b) Discuss with neat sketch the difference between detonation in S.I. engine and diesel knock.

Q: It is a heat transfer question. Please briefly explain.

A: Dear student, According to the guidelines I am allowed to answer only three sub-p...

Q: In a diesel engine, r=18, alfa=2.8 T1=336 K, P1=100kPa Vh=740 cm3.The polytropic base in the compres...

A: Given data: Compression ratio r =18 fuel cut of ratio α =2.8 in...

Q: a) Define Radiation and give at least 3 examples.

A: Heat transfer: It is the flow of heat from one object to another object due to temperature differen...

Q: QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N. Calculat...

A: Given data: Diameter of rope, d=1 cm= 10mm Tensile load on the rope (along the axis), P=120N.

Q: Insulated water tank 2. Water (0.12m3) 3. 4. 5. 6. COPPER A 50-kg copper block initially at 80°C is ...

Q: Determine the components of the force and its moment about point A.

Q: Refrigerant-134a at 1 MPa and 90°C is to be cooled to 1 MPa and 30°C in a condenser by air. The air ...

Q: If the perpendicular force of 1000 N, acting on a surface of area, 0.05 m^2, calculate the pressure ...

A: Given F = 1000 N A = 0.05 m2

Q: The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinde...

A: Given data as per questionHead diameter(D)=300 mmbolt dia(d)=10 mmEb=200 GpaEm=90 GpaInitial tightin...

Q: A 1.0-mm-diameter wire is maintained at a temperature of 400°C and exposed to a convection environme...

A: h=heat transfer coefficient=120 W/m-°CT1=Temperature of wire maintained=400 °CT2=Ambient Temperature...

Q: 12.You are tasked to water the plants outdoor. What happens to the speed of thewater when you half-c...

A: If we cover half opening of hose with our thumb then the velocity as well as pressure of water comin...

Q: A shell &tube heat exchanger has 4 tube passes. Oil inters to the tubes with 100oC . Mass flow r...

Q: Which one of the below is one of the advantages of Mechatronics? O A) Requirement of Knowledge from ...

A: Mechatronics is the combined branch of mechanical and electronics. With the help of mechatronics, me...

Q: At 100°C water has a specific latent heat of vaporization of 2260 000 J/kg. What does this mean? A. ...

A: At 100o C water has a specific latent heat of vaporization of 2260000 J/kg. What does this mean? Ans...

Q: The solid spindle AB has a diameter ds=40mm and is made of a steel with G=110GPa and Tem=120MPa , wh...

Q: At a crossroads, vehicle B heading south and vehicle A heading north-east at an angle of 300 collide...

A: Write the given data with suitable variables. mA=1500 kgmB=1200 kgvA=50 km/hr

Q: solve please ..

A: The torque acting on the shaft is given. resolve the torque on the shaft as shown below, The torque...

Q: FACULTY OF SCIENCES QUESTION NO. 2: In Figure 2, a block m; (m; =1.0 kg) on a frictionless inclined ...

Q: Which type of oil filter uses an anti drain back valve to prevent it from emptying of oil when the e...

A: Which type of oil filter uses an anti drain back valve to prevent if form emptying of oil when engin...

Q: Determine the reactions at the pin A and the tension in cord BC. Set F=40 kN. Neglect the thickness ...

A: Considering a beam fixed at a point and attached by cable and attached to a point. Applying the sign...

Q: Define the following:a) Heat Exchanger.b) What is the difference between a condenser and heat exchan...

A: Heat Exchanger A heat exchanger is a device which is used to transfer heat from one fluid to another...

Q: Mechanical Vibration lesson A simple-simply supported beam subjected to a uniformly distributed harm...

Q: Specify the type of compound truss and determine the force in members JH, BJ, and BI. State if the m...

A: Moment acting about point A is Fy40=1.530+220+1.530Fy=2.875k in vertical equilibrium condition Ay+Fy...

Q: Why every condenser is not a heat exchanger?

A: Condenser is a device in which fluid changes its phase from vapour to liquid by rejecting its latent...

Q: How would you solve this

A: a) Given Pounds = 248 Solution 1 Pound = 4.4482 N Therefore, 248 Pound...

Q: Situation 7: A truss is made of timber having the dimensions and load drawn as shown. The allowable ...

A: Draw the FBD of the diagram as shown below.

Q: Heat transfer question

Q: The beam AB in the figure is balanced from the point a by the simple support from the point B with a...

A: For the given beam To determine the bending moment at section a-a (in kN-m)

Q: 2. A piston/cylinder with a cross-sectional area of 0.01 m² has a piston mass of 100 kg resting on t...

A: Given Data⇒Cross-sectional area A=0.01 m2Massm=100 kgOutside atmospheric pressureP0=100 KPaProblem d...

Q: An intermediate shaft is running at constant speed as shown in Figure 3. The shaft to be made from A...

Q: basic rigid motion is both angle preserving and distance preserving.

A: 1. A rigid motion is a transformation (of the plane) that "preserves distance". In other words, if A...

Q: cc BY UBC Engineering The 3 kg block sits on the edge of a 1 m disk that is accelerating with a rope...

A: Given Mass, m = 3 kg Diameter, d = 1 m Velocity, v = 7 m/s Find The tension, ...

Q: Air in a piston cylinder arrangmemt undergoes a process Pv^1.3 =C. During this process 10 kJ of heat...

A: Given data: The polytrophic index is n = 1.3. The heat added is QP = 10 kJ.

Q: Two vessels of equal volume are connected by a short length of pipe containing a valve. One vessel c...

A: Let Initial volume of both the vessel : V1= V & V2 =V When the vaccume will filled by the ...

Q: In a 4-cylinder 4-stroke KA engine with volumetric efficiency ɳv=0.85, compression ratio 14: suction...

Q: If your odometer reading is 20000 (miles) and your new tires have a circumference of 101.5. How far...

A: Odometers generally work by counting the number of rotations of the wheel and then multiplying it by...

Q: r The bottle shown rests at a distance of 3 feet from the centre of the horizontal platform. If the ...

A: The linear speed of any object to move in the circular path is known as tangential velocity. Given D...

Q: A steel tube having k = 46W / m . °C has an inside diameter of 3.0 cm and a tube wall thickness of 2...

A: givenK=46w/m oCsteel tube inside diameter d1=3.0 cm a tube wall thickness t=2 mmthe inside of the tu...

Q: The minimum and maximum temperatures of a Brayton cycle is given as 295 K and 1400 K, respectively. ...

A: Given data :- Minimum Temperature T1 = 295 K Maximum Temperature T3 = 1400 K Pressure ratio r = 13...

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

End B of the 60-lb homogeneous bar is pulled by the 80-lb force inclined at 45° to the horizontal. Find θ, the angle of inclination of the bar.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The three bars are welded together to form a rigid unit that is supported by three slider bearings. Neglecting the weights of the bars, determine the magnitudes of the three bearing reactions caused by the 120-lbin. couple.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
A moment of 50lbft about O is required to loosen the nut. Determine the smallest magnitude of the force F and the corresponding angle that will turn the nut.
The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900 lb, find the smallest possible sag hC at C.
The 1800lbin. couple is applied to member DEF of the pin-connected frame. Find the internal force systems acting on sections 1 and 2.
The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.
The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The 1200-lb homogeneous block is placed on rollers and pushed up the 10 incline at constant speed. Determine the force P and the roller reactions at A and B.
The pulley-cable system supports the 150-lb weight. The weights of the pulleys and the horizontal bar ABC are negligible. Determine the cable tensions at A and C and the distance x.
The woman is trying to move the crate of weight W by pulling on the rope at the angle to the horizontal. Find the smallest possible tension that would cause the crate to slide and the corresponding angle .