What are the major differences between aerobic and anaerobic sealants

Q: Square ring,shaped ring and O ring seals are the seals which could be utilized for _____________…

A: Objective: To determine the use of the seal for a different type of flow.

Q: A mirror and a quality light for leak testing may be used in lubrication repair. Select one: O True…

A: General components used for lubrication repair are: Wrenches of different sizes to remove the oil…

Q: Which of these equipment that does not belong to the class of equipment listed below Pneumatic tired…

A: Answer is b).Bitumen distributor.

Q: What is the best option for removing a stuck coolant hose? Select one: a. Twisting the hose off with…

A: A technician's primary responsibility is to prevent vehicle breakdowns. Cooling system failures are…

Q: State two reasons copper pipe is becoming more popular for fire protection systems

A: Almost all fire protection systems use carbon steel, but the use of copper in fire protection…

Q: Discuss reverse-airflow cleaning methods in detail.

A: given: Discuss reverse-airflow cleaning methods in detail.

Q: Performance evaluation of centrifugal pump and sealless pump, trends, cost evaluation, and…

A: Mechanical seals are used to make seal on exit and inlet point of the roatating shaft.

Q: Full film lubricating is a type of lubrication in which the coefficient of friction is low. Select…

A:

Q: Coolant hoses are being discussed. Technician A states that many manufacturers recommend coolant…

A: Coolant hoses are to be maintain and replace in certain time interval, it fails due to high…

Q: Why preventive maintenance paramount

A: Preventive maintenance is basically when factory maintenance teams inspect equipment to identify…

Q: When changing a cartridge oil filter, the only parts that get replaced are the paper filter…

A: Answer : O-rings

Q: Give at least 2 examples of an automotive job where cleaning and priming is applicable.

A: Given Automotive job To find Cleaning and Priming in automotive job

Q: Make a procedure on how to prepare a surface for sealant/ adhesive application.

A: Write down the procedure to prepare a surface for sealant/ adhesive application.

Q: What’s is the purpose of breaking in new disc pads

A:

Q: While installing new brake pads: Technician A coats the caliper bushings with silicone grease before…

A: Both A and B

Q: Identify the property of lubricant, in which the oil blocks the circulation pipe due to the presence…

A: Answer is oxidation

Q: Tech A says that the use of some RTV sealants to seal components on an engine can damage the oxygen…

A: Among all the sealants, the pliable silicone sealants like RTV are commonly used sealants while…

Q: Hard drawn copper rivets are u

A: Answer: d= 0.36in

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: When rigid fluid lines are attached to an aircraft structure with cushion clamps, the clamps should…

A: Solution:

Q: What areas within a vane pump or motor are the most susceptible to contamination-induced clearance…

A: Vane Pump :  A vane pump is a type of positive displacement pump that delivers a constant flow rate…

Q: Brake linings should be replaced when __ .a. linings are worn to within 1 /32 inch of a rivet headb.…

A: When brakes are exposed to wet, damp conditions, such as after a rain storm, pads may exhibit a very…

Q: Actions to be taken including HSE considerations while freeing the stuck pipe which include the…

A: The drilling jars are the tools that are present on the drill string. The jar enables to knock the…

Q: What are the differences between hydraulic vise and screw vise with

A: A vice features two parallel jaws that operate together to clamp and hold an item securely. The…

Q: Assume that after removing the cylinder head of an engine, a wet, oily condition is noticed on the…

A:

Q: Introduction to pneumatics

A: Pneumatics: It is the branch of science and technology of pressurized air—using piped, compressed…

Q: rudders

A:

Q: Explain the procedure and regulations for hydraulic and pneumatic components maintenance

A: Proper Procedure and regulations for hydraulic system... Clean the area around dipsticks, fill plugs…

Q: Technician A says that coolant hoses should be squeezed to check for hardening or softening.…

A: Solidly squeeze both the upper radiator and radiator hoses. They ought to feel firm, solid, and…

Q: In this personal protective equipment determine the: PPE Is training required in OSH? How to…

A: OSH is the Occupational Safety and Health administration in which various safety rules and equipment…

Q: Industrial issues that can be solved by conveyor belt water cleaning machine.

A: Belt cleaners with superior performance keep belts clean, reducing carryback and improving belt…

Q: While installing new brake pads: Technician A coats the inside diameter of the bushings with…

A: Vehicle maintenance is an important task for the efficient working of vehicles. Vehicle maintenance…

Q: submit at least 10 hazard symbols and its description used in a workplace. identify the workplace…

A: There are a lot of hazard symbols which are used in industries. Some of them are listed below.

Q: The materials used for piston rings should not be wear resistant O a. FALSE O b. TRUE

A: 1). Work of position is To reciprocate into the cylinder. so, it is continuously rubbing with piston…

Q: What is the difference between splash lubrication system and dry sump lubrication system?

A: The difference between the splash lubrication system and the dry-sump lubrication system is given…

Q: and the elasticity of the bumpers ounts..

A: During an effect of a car with a boundary flexibility of radiator, guards, sheet metal body, motor…

Q: 15) What is Automobile ty tubeless tyre

A: In other word we can say that tire is a ring-shaped component that surrounds a wheel's rim to…

Q: List the more common seal configurations and draw their cross sections.

A: Some of the common seal configurations are : Rod seal Piston seal Face seal

Q: Q2.Types of Shaft Coupling.

A: Types of shaft coupling :-

Q: factors affecting the force impacted by jet on defelcter

A:

Q: t and clean handwritten solution

A: It is an alloy of iron that has 2 to 4% of carbon present in it. It can be obtained by reducing the…

Q: 11. Fluid sealing in a dashpot is achieved using

A: GIVEN DATA A MCQ GIVEN ASKING WHICH SEALING USED IN FLUID DASHPOT SYSTEM

Q: Check valves are installed in pipelines and tubing to prevent such a back flow and to permit the…

A: Check valves are installed in pipe lines and tubing to prevent such a back flow and to permit the…

Q: Which of the following is NOT one of the seal types used in hydraulic systems? O Piston cup packings…

A: Hydraulic system: The system in which power transfers with the help of pressurized fluid from one…

Q: the effect of the smooth surface equal effect roller in support

A: yes

Corrosion control methods

Corrosion may be defined as the method in which metals are attacked on their exteriors by gases existing in the atmosphere, converting them to their oxides, nitrides, sulfides, etc.