Answered: to provide a good sealing joint between…

to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface true or false

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter7: Tubing And Piping

Section: Chapter Questions

Problem 11RQ: The portion of a compression fitting that actually tightens against the tubing to create the...

See similar textbooks

Related questions

Q: Part of the screw thread connecting the adjacent flank on top of the screw thread is known as O…

A: Correct answer is option (b) Pitch The pitch of a thread is the distance measured parallel to its…

Q: Question: To install the front cover on an engine, position its either on the or on the cover…

A: A gasket is a flat rubber piece that fills the space between two metal surfaces in the engine or…

Q: 11. A rear flange mounted cylinder extends 14 in. under a load of 10,000 Ibf. What size cylinder rod…

A: Given Mass, m = 10000 lbf = 4535 kg Extension, h = 14 in…

Q: Radial and axial tolerances in the ball joints are checked using a _____. a. beam-type torque…

A: The lower control arms must hang free, so the jack is positioned under the frame, not the lower…

Q: This part of the a cylinder holds the piston in place and helps support the rod as it extends. a.…

A: Option c is correct.

Q: Members that are joined together to form a kinematic chain Link Bar Pin Joint

A: As per company's guidelines we can answer only first question.

Q: Which of the following is the most common method of snug tightening bolts? O Heat tightening O…

Q: Cast iron is used to make rollers as it has superior compression load. Select one: True False

A: The above statement is false.

Q: During drilling operation, work piece must be held in vice. Select one: True False

A: Given Statement : During drilling operation, work piece must be held in vice. Select one: True…

Q: 1.Name type of failures in engine blocks

A: The engine is the most important part of the IC engine. In production, Every company produces an…

Q: The piston rings are used to act as a seal between the piston and cylinder head a. FALSE b. TRUE

A: We have to determine true /false of The piston rings are used to act as a seal between the piston…

Q: Drag text boxes to label diagram of a typical valve spring retaining mechanism

A: Valve is a mechanical device that is used to to provide the passage to the inlet or exhaust of a…

Q: en expanded isothe nally compressed a to the init

Q: When changing a cartridge oil filter, the only parts that get replaced are the paper filter…

A: Answer : O-rings

Q: ch of 6 mm. Th d collar friction

Q: Identify parts of an engine lubrication system using this schematic drawing Oil Sump

A: given; identify parts of engine lubrication system.

Q: Make a procedure on how to prepare a surface for sealant/ adhesive application.

A: Write down the procedure to prepare a surface for sealant/ adhesive application.

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

Q: Hard drawn copper rivets are u

A: Answer: d= 0.36in

Q: tive and compression negative. 45°

A: Draw the free body diagram for the above problem as follows.

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: • Use hexagonal head screw/bolt with jam locking nut through clearance holes to fix the two parts…

Q: Which of the following statements pertaining to the steel tubing is not true: Steel tubes are…

A: Given: Steel tubes are better than steel pipes because, they: are less expensive.…

Q: -kt 8. L[e*² + 2π - tª] = -1

A: As per our guidelines we are supposed to answer only one question in case of multiple questions…

Q: Assume that after removing the cylinder head of an engine, a wet, oily condition is noticed on the…

Q: tail force

A: Tail force is 15kN

Q: Determine the maximum, minimum and average pressure in a plate clutch

A: Given data; Axial force(W)=4kn=4×103 NInside radius (r2)=50mmoutside radius(r1)=100mm Assume…

Q: SoNe for a minímum bolt diameter minimum thickness of plate the rivets are atfached to Given: wad =…

Q: Temporary joint is obtained by one of the following. (A) Interference fit (B) welding (C) Riveting…

A: Given data Temporary joint is obtained by one of the following

Q: Where should the temperature difference be the greatest to make the Sirling engine operate well? O…

A: A Stirling engine operates by the expansion and compression of a working fluid (Mostly gas) and so…

Q: Question: Q1: Write At Least One Case Study Of The Following Seals 1. Labyrinth Seal 2. Lip Seal 3.…

Q: An oil leak at the bellows of a rack and pinion could be caused by ______.

A: As per given question What is the cause of Oli leak at bellows of a rack and pinion

Q: force Frequired to hold the plug in its position

A: Given; Consider a frictionless, massless and leak proof plug blocking a rectangular hole of…

Q: The materials used for piston rings should not be wear resistant O a. FALSE O b. TRUE

A: 1). Work of position is To reciprocate into the cylinder. so, it is continuously rubbing with piston…

Q: Large cars with long drive shafts often use a double-U-joint arrangement called a __ .a. Spicer…

A: A universal joint is a mechanical connecting device that is used between the rotating shafts and the…

Q: The fluid leaves the impeller with more velocity head Select one: True False

Q: If the oil on the dipstick looks milky gray, it is possible that there is water (or coolant) being…

A: Solution:

Q: List the more common seal configurations and draw their cross sections.

A: Some of the common seal configurations are : Rod seal Piston seal Face seal

Q: Where is the rod end of the cylinder?

A: Given: To identify the rod end of cylinder.

Q: Q2.Types of Shaft Coupling.

A: Types of shaft coupling :-

Q: The 3 basic oil seal designs to keep fluids from escaping around a rotating shaft are?

A: The three basic oil seal design to keep fluid from escaping around a rotating shaft are-

Q: The spool is sealed along the clearance between moving spool and O housing (valve body) O case O…

A: given; The spool is sealed along the clearance between moving spool and ...

Q: What type of caps are used to hold the crankshaft in place once it’s installed in the block?

A: Crankshaft is a shaft used in engine to convert a linear motion of piston to a rotational motion. It…

Q: The inside of a hydraulic power unit is shown. Identify pats A,C, and E

A: Solution: Given Data:

Q: What is the axle pressure on the front axle (which is standing on the quay)?

A: Draw the free body diagram of the beam.

Q: the effect of the smooth surface equal effect roller in support

A: yes

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Concept explainers

Corrosion control methods

Corrosion may be defined as the method in which metals are attacked on their exteriors by gases existing in the atmosphere, converting them to their oxides, nitrides, sulfides, etc.

Question

to provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface

true or false

Expert Solution

Step 1

Question:-

To provide a good sealing joint between the cylinder head and exhaust, apply a sealant to the machined surface

Step by step

Solved in 2 steps

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The portion of a compression fitting that actually tightens against the tubing to create the leak-free seal is the A. union. B. coupling. C. compression nut. D. ring or ferrule.
While discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor B
Why is it important to loosen the cylinder head bolts in the recommended order?
The three major types of rubber seals used in automatic transmission are the blank the blank and the blank
The piston rings are used to act as a seal between the piston and cylinder head a. FALSE b. TRUE
Select the two seals used to sealing active elements of a pump or compressor to retain the pumped fluid: U-cup O-rings V-packing piston rings face seals lip seal
Select the four seals commonly used to sealing around continuously reciprocating rods or pistons: piston rings lip seal U-cup face seals V-packing O-rings
The clutch, or friction, disc is connected to the. a. engine crankshaft b. transmission input shaft c. transmission output shaft d. transmission countershaft
Technician A inspects all sealing surfaces for damage and uses a supplementary sealant on the gaskets if the surface is questionable. Technician B coats the intake gasket on some engines with a nonhardening sealer. Who is correct? Technician A Technician B Both A and B Neither A nor B
The clutch, or friction, disc is connected to the
This part of the a cylinder holds the piston in place and helps support the rod as it extends. a. rod seals b. rod bushing c. pistons seals d. rod brushing
Clutch break and gear Solve it by proper solution