Define relay

Q: What is the function of Relay?

A: Relays are electric switches that use electromagnetism to convert small electrical stimuli into…

Q: Diagram a circuit that would allow for the manual lowering of a load on a cylinder using a simple…

A:

Q: Type of Mechanism

A: As given in question we have to match the following mechanism; hence; (P) SCOTT (Q) Geneva mechanism…

Q: Explain the operation of Buchholz relay.

A: Buchholz relay Buchholz relay in a transformer is an oil tub containing the connecting line from the…

Q: Define the following, Joint. Link. Joint space. Actuator space.

A: Joint: A point where two or more than two links are connected is known as joint. Link: It is a…

Q: State four advantages of a pre-engaged starter when compared with an inertia type.

A:

Q: Define drive head

A: Given Data⇒ drive head Problem statement⇒ Problem says Define drive head

Q: explain anchor cable with sketch

A: A heavy chain is used to hold the vessel at anchor. The chain is made of links and the length of…

Q: Explain the installation procedures of a flexible coupling

A: given; explain the installation procedures of a flexible coupling.

Q: Name the five terms used to describe a thread.

A: for detailed answer refer below images.

Q: The two types of relays used to start hermetic compressorsare the _________ relay and the _________.

A: The hermetic compressor are the special type of compressors. These compressor are very big in size.…

Q: Explain  what is follower mechanism.

A:

Q: le for the key to fail in an overload condition rather than more costly

A: While designing a shaft it is always use to design key weekend . Because in case of failure less…

Q: a. Explain resonant earthing system with diagram b. How will you give Combined Leakage and Overload…

A: (a) Resonant earthing system : Resonant earthing is a sure uncommon sort of high impedance earthing…

Q: Draw the Circuit diagram for holding the cylinder of double acting cylinder in the fully extended…

A: Directional control valves follow or perform only three functions: 1) Stop Fluid Flow 2) Change the…

Q: Define sensors and list the various specifications that need to be carefully studied before using a…

A: Sensors It is a device which converts signals from one energy domain to electrical domain. The…

Q: Name and describe the two principal types of conveyor holdbacks

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: Name three types of automatic controls.

A: Given Data : Automatic controls

Q: 4. Describe two type of starting system principles and draw the basic starting circuit

A: The starting system is a combination of mechanical and electrical parts that work together to start…

Q: ist two main types of robot joints ar

A: The moveable components of the robot that result in relative motions between adjacent connections…

Q: Write briefly about the 4/3 lever operated DCV which is used for doing the practical with symbol and…

A: Directional control valves are widely used in industries where fluid applications are involved. They…

Q: The Mobility of a four bar change point mechanism is O 1 O 3 O 4

A: Consider : - The number of links is l. The number of lower pair is j. The number of higher pair is…

Q: an der Waal for I cross links.

A: In the above question all the options are incorrect Stiffness of thermosets are high

Q: What is the Relay Number and its law?

A: Rayleigh Number It is the product of grashof No. and Prandtl No. Grashof No. shows the relation…

Q: What is Belt-conveyor system?

A: The belt conveyor system is essential in a material handling industry. It is used to transport bulk…

Q: 4. What are the advantages and disadvantages of using the Wet Mount technique?

A: advantage: Wet-mount: A microscope slide specimen is suspended in a drop of liquid located between…

Q: If 4 links are connected at the same joint, the joint is equivalent to binary joint.

A: This question is from theory of machine.  Here given is that 4 links are joined at a one connection…

Q: What is an attenuator used for?

A:

Q: When rope drive is preferred?

A:

Q: .Explain belt driven starters and mention its advantages

A: Belt driven starters A belt driven starter motor system used to start an internal combustion engine.…

Q: What is a coupling

A: Coupling is a commom word used in the field of mechanical engineering which means joining or…

Q: Entire frame, pulleys, and contacting cable to be isolated as a single unit. B

A: TO draw the FBD of the given system we have to consider the weight and forces applied to the system.…

Q: Fill in the blank which is given below If 2 links are connected at the same joint, the joint is…

A: when x number of links are connected to the same joint then the binary joint formed is x-1 binary…

Q: Problem: Boxes (or certain production parts) are moved by a double-ac cylinder away from a…

A: This  problem is solved using Pneuma solver software.

Q: A- Draw a detailed schematic of a PUMA robot (show all joints, axes of  motion and link lengths)?…

A: PUMA stands for :  Programmable Universal Machine for Assembly

Q: Types of couplings

A:

Q: In a DCV, this part is located on either or both sides of the spool to position it in the middle…

A: DCV is the directional control value that performs 3 functions, 1. Allow the fluid flow, 2. Change…

Q: The two types of motors used for hermetic compressorsare _________ and _________.

A: There are basically four types of single-phase motors in use in hermetic assemblies: the permanent…

Q: Explain the Interruption Cycle with neat sketch

A: The Interruption cycle (also known as the fetch–decode–execute cycle) is the cycle that the…

Q: Draw and design a bushed pin type flexible coupling

A: The Answer is below

Q: Discuss the implementation of a split range control in boilers with a necessary diagram.

A: Spilt Range Control: Spilt control device is used to control the two final elements with a single…

Q: Construct a circuit drawing of a hydraulic dump lift using an open center circuit.

A: To construct an open center circuit of a hydraulic pump

Q: For the mechanism below: Rolling contact

A: Given Data⇒ Problem definition⇒ Problem says determine