The figure shows the cross section of a standard L80 × 60 × 10-mm structural steel, unequal angle section. Neglecting the effects of the small corner fillets, compute Ixy of the cross-sectional area.

Q: A 30 cm X 16 cm rolled steel joist of I-section has flanges 11 mm thick and web 8 mm thick. Find the...

A: Given that, I-section,Width of flange=30 cmHeight of web=16 cm,Thickness of flange=11 mm,Thickness o...

Q: a) With a neat sketch explain about Induced soft foot.

A:

Q: Answer in picture containing the question. Kindly before submitting the solution.

A: Given:When the block is released the cord is straight. Neglect friction To find: The acceleration wh...

Q: A bar of titanium alloy of length 120mm and square cross – section, 7.5 mm x 7.5 mm, is pulled axial...

A:

Q: 6

A: Angle of the curve is: α=3° Angle of intersection is: θ=24° Radius of curve is R=1146α=11463=382 m

Q: Bar AB rotates uniformly about the fixed pin A with a constant angular velocity ω. Determine the vel...

A:

Q: Describe the process for validating a water purification system.

A: Water purification has become a necessity in todays world and thus, validation of water purification...

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting s...

A:

Q: Chapter Six Vibrations b) Find the differential 2a equation for small oscillations C in terms of (0 ...

A: Given data: Beam with springs and damper attached as shown above   To determine: Differential equati...

Q: A cylindrical pressure vessel has an internal diameter of 1600 mm and is subject to an internal flui...

A: Given, d=1600 mm p=30 bar = 3 MPa = 3 N/mm2 t= 15 mm σu= 600 N/mm2 ηc = 50% ηL = 80%

Q: Steam inters a turbine at 21 kg/s as shown in the figure, find the exit temperature?

A: Qout  = 639 kW  W = 12240 kW  P1 = 1.6 Mpa  T1 = 350°C  m = 21 kg /s 

Q: For the beam shown, determine the reactions of the left and right supports tomaintain equilibrium in...

A:

Q: Solve step by step

A: It is known that the moment of inertia of a solid sphere is Here, Ro is the radius of the sphere. R...

Q: E Volumetric analysis for a gas mixture is given as: Hy: 10% ; N: 30% ; co : 40% ; Co, : 20% If the ...

A: "As per policy i have solved three sub parts for you please resubmit the remaining questions."   Dat...

Q: i need the exercise 2.4 please show details.   thermal conductivity value of the insulation IS 0.021...

A:   Given : k=0.021 Btu ft/hft2°Fh∞=2 Btu /hft2°F              

Q: If the flywheel is rotating with an angular velocity of  ωA=6 rad/s, determine the angular velocity ...

A: Solution: Given Data: *The angular velocity of the flywheel is 6 rad/s.

Q: Q.1) A 50 kg block is dropped from a height of 2 m onto the the 20 kg pan of a spring scale. Assumin...

A:

Q: Please answer this attached question and explain the method briefly... Thank you

A: This is a steam power plant, so this plant will works on Rankine cycle. From the above information t...

Q: A machine vice, as shown in Fig. 6.12, has single-start, square threads with 22 mm nominal diameter ...

A:

Q: please use international values

A: GIVEN:*Compression ratio r=19*Cut-off ratio ρ=3*T1=37°C=310 K*P1=100 kPa*HAP=950 kJ/kg   TO FIND:-Te...

Q: Two identical sinusoidal waves with wavelengths of 2 m travel in the same direction with the same sp...

A: Write the given dat with suitable variables: λ=2 m∆x=2 m

Q: Mechanical Engineering Question

A:

Q: Water with a quality of 53,5% and pressure of 200 kPa is inside a rigid tank. The tank  is heated  b...

A: The initial state of water in a rigid tank 53.5% dryness fraction and 200 kPa pressure Heat supplied...

Q: Please help me with this I’m having trouble

A: Energy conversion: (1) When the person pulls the cord, the mechanical energy is transferred to the e...

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Eva...

A: The angle made by the force F with line OA (n) and with line perpendicular to OA(t) can be calculate...

Q: Find the moment of inertia about centrodial x-axis and centroidal y-axis of the given geometry.

A: Consider the diagram shown below for the given figure.

Q: 10-122 Locate the principal axes and determine the max- imum and minimum moments of inertia for the ...

A: Moment of Inertia is the integration of area  over the volume. In This Question Two Normal Area port...

Q: Consider the piping system shown. The average speed of water flowing through the 12-inch-diameter se...

A:

Q: For the pin-jointed truss in Figure (7), (a) detemine the reactions at the supports at A and C, and ...

A: Given: The truss is shown below:

Q: The wall of a house, 8.09 m wide and 6.70 m high is made from a thick bricklayer with thermal conduc...

A:

Q: If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order to hold theassembly in...

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.