19. knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) thediameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) thecorresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in eachsupport bracket at C.75 mm9 mm300 mmPI125 mmD5 mm 20. The two portions of member AB are glued together along a plane forming an angle 0 with thehorizontal. Knowing that the ultimate stress for the glued joint is 2.5 ksi in tension and 1.3 ksi inshear, determine the range of values of 0 for which the factor of safety of the members is at least3.0.2.4 kips1.25 in.2.0 in.

Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

). knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the ameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the orresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each "pport bracket at C. 75 mm 9 mm - 300 mm- B 125 mm D

). knowing that a force P of magnitude 75 N is applied to the pedestal shown, determine (a) the ameter of the pin at C for which the average shearing stress in the pin is 40 MPa, (b) the orresponding bearing stress in the pedestal at C, (c) the corresponding bearing stress in each "pport bracket at C. 75 mm 9 mm - 300 mm- B 125 mm D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall thickness. Knowing that the maximum stress after the offset is introduced must not exceed 4 times the stress in the tube when it was straight, determine the largest offset that can be used.
A steel pipe of 400-mm outer diameter is fabricated from 10-mm-thick plate by welding along a helix that forms an angle of 20°with a plane perpendicular to the axis of the pipe. Knowing that the maximum allowable normal and shearing stresses in the directions respectively normal and tangential to the weld are σ = 60 MPa and τ = 36 MPa, determine the magnitude P of the largest axial force that can be applied to the pipe.
Knowing that, for the plate shown, the allowable stress is 125 MPa, determine the maximum allowable value of P when (a) r=12 mm, (b) r= 18 mm
Knowing that the hole has a diameter of 9 mm, determine (a) the radius rf of the fillets for which the same maximum stress occursat the hole A and at the fillets, (b) the corresponding maximum allowable load P if the allowable stress is 100 MPa.
In the structure shown, an 8 mm diameter pin is used at A, and 12 mm diameter pins are used at B and D. Knowing that the allowable shearing stress is 120 MPa at all connections and that the allowable normal stress and bearing stress is 240 MPa in each of the two links joining B and D, determine the allowable load P
Knowing that the machine component shown has a trapezoidal cross section with a = 2.5 in. and b = 3.5 in., determine the stress at point A and at point B. Take M = 80 kip·in. The stress at point A is ksi. The stress at point B is ksi.
For the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx= 14 ksi, σy= 9 ksi, and σmin= 5 ksi. Determine (a) the orientation of the principal planes, (b) the principal stress σmax, (c) the maximum in-plane shearing stress
A torque of magnitude T=12 kN·m is applied to the end of a tank containing compressed air under a pressure of 8 MPa. Knowing that the tank has a 180-mm inner diameter and a 12-mm wall thickness, determine the maximum normal stress and the maximum in-plane shearing stress in the tank.
Two loads are applied to the bracket BCD as shown. (a) Knowing that the control rod AB is to be made of a steel having an ultimate normal stress of 600 MPa, determine the diameter of the rod for which the factor of safetywith respect to failure will be 3.3. (b) The pin at C is to be made of a steelhaving an ultimate shearing stress of 350 MPa. Determine the diameter ofthe pin C for which the factor of safety with respect to shear will also be 3.3.(c) Determine the required thickness of the bracket supports at C, knowingthat the allowable bearing stress of the steel used is 300 MPa.
For the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx = 15.5 ksi, σy = 9 ksi, and σmin = 5 ksi. Determine the orientation of the principal planes. Determine the principal stress σmax. Determine the maximum in plane shearing stress
Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts fitting snugly inside cylindrical brass spacers.Knowing that the average normal stress must not exceed 200 MPa in the bolts and 130 MPa in the spacers, determine the outer diameter of the spacers that yields the most economical and safe design.
A single horizontal force P with a magnitude of 150 lb is applied to end Dof lever ABD. Knowing that portion AB of the lever has a diameter of 1.2 in., determine (a) the normal and shearing stresses located at point H and having sides parallel to the x and y axes, (b) the principal planes and princi-pal stresses at point H.