Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf splice as shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine i. the largest load P that can be safely applied ii. the corresponding tensile stress in the splice. 75 mm

Two wooden members of uniform rectangular 150 mm cross-section are joined by a simple glued scarf splice as shown. Knowing that the maximum allowable shearing stress in the glued splice is 620 kPa, determine i. the largest load P that can be safely applied ii. the corresponding tensile stress in the splice. 75 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the structure shown, an 8 mm diameter pin is used at A, and 12 mm diameter pins are used at B and D. Knowing that the allowable shearing stress is 120 MPa at all connections and that the allowable normal stress and bearing stress is 240 MPa in each of the two links joining B and D, determine the allowable load P
In the structure shown, an 8-mm diameter pin is used at A, and 12-mm diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor ofsafety of 3.0 is desired.
Two wooden planks, each 1212 in. thick and 9 in. wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 1.8 ksi, determine the magnitude P of the axial load that will cause the joint to fail. The magnitude P of the axial load that will cause the joint to fail is kips.
Knowing that the hole has a diameter of 9 mm, determine (a) the radius rf of the fillets for which the same maximum stress occursat the hole A and at the fillets, (b) the corresponding maximum allowable load P if the allowable stress is 100 MPa.
Two wooden members of 80 *120-mm uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that β=22° and that the maximum allowable stresses in the joint are, respectively, 400 kPa in tension (perpendicular to the splice) and 600 kPa in shear (parallel to the splice), determine the largest centric load P that can be applied
Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that P =11 kN, determine the shearing stresses in the glued splice.
Two wooden planks, each 7/8 in thick and 6in wide, are joined by the glued mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 120psi, determine the smallest allowable length d of the cuts if the joint is to withstand an axial load of magnitude P=1200-lb. Note: Seven surfaces carry the load, P=1200-lb
Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that P=11 kN,determine the normal and shearing stresses in the glued splice.
Two loads are applied to the bracket BCD as shown. (a) Knowing that the control rod AB is to be made of a steel having an ultimate normal stress of 600 MPa, determine the diameter of the rod for which the factor of safetywith respect to failure will be 3.3. (b) The pin at C is to be made of a steelhaving an ultimate shearing stress of 350 MPa. Determine the diameter ofthe pin C for which the factor of safety with respect to shear will also be 3.3.(c) Determine the required thickness of the bracket supports at C, knowingthat the allowable bearing stress of the steel used is 300 MPa.
A load P is applied to a steel rod supported as shown by an aluminum plate into which a 0.6-in.-diameter hole has been drilled. Knowing that the shearing stress must not exceed 18 ksi in the steel rod and10 ksi in the aluminum plate, determine the largest load P that may be applied to the rod.
In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 2.6 is desired.
An open-link chain is obtained by bending low-carbon steel rods of 0.5-in. diameter into the shape shown (Fig. ). Knowing that the chain carries a load of 160 lb, determine (a) the largest tensile and compressive stresses in the straight portion of a link, (b) the distance between the cen-troidal and the neutral axis of a cross section