3. The 1.5 inch diameter pins at A, B, and C that support the structure are in singleshear. Find the largest force F that can be applied to the structure if the working shearstress for these pins is 4000 psi. Consider the weight of member AB as 1400 lbs and formember BC as 1700 Ibs.B6 ft i2 ft4 ft3 ft C

Answered: Image /qna-images/answer/7ad6dc39-8651-4430-a78a-e75c3aaf1ae4.jpg

. The 1.5 inch diameter pins at A, B, and C that support the structure are in single hear. Find the largest force F that can be applied to the structure if the working shear tress for these pins is 4000 psi. Consider the weight of member AB as 1400 Ibs and for nember BC as 1700 Ibs. 6 ft 2 ft 3 ft C 4 ft

. The 1.5 inch diameter pins at A, B, and C that support the structure are in single hear. Find the largest force F that can be applied to the structure if the working shear tress for these pins is 4000 psi. Consider the weight of member AB as 1400 Ibs and for nember BC as 1700 Ibs. 6 ft 2 ft 3 ft C 4 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
compute the force in member FJ
From the given truss , compute the force in member CE. a.187.5 N (C) b.62.5 N (C) c.62.5 N (T) d.37.5 N (C
In the beam shown, take W1 = 9 kN/m, M1 = 25 kN-m, and P1 = 22 kN.a) Determine the shear at "D"
For the truss shown below is supported by a pin at A and roller at F. If it is loaded with P (kips)at joints B and E, determine the force in members AD, GH, BD, CE, and DG. P(kN) = 516
From the given cantilever truss shown supported by hinged A and roller at B. culate the force at FG. A.) 12.4 N b.) 10 N c.) 16.2 N d) 8.78 N
The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Use the method of sections to determine the force in members IF, IM andBD.
The Channel section is used as a purlin placed on top of trusses with spacing of 4 m and slope 1V to 4H. The purling are supporting a total uniform load of 24 kN/m. Properties of Channel: Sx = 119 x 10^3 mm^3 Sy = 87 x 10^3 mm^3 Compute the maximum bending stress if supported by sagrods at third points. Round your answer to 2 decimal places.
Compute the force in member BD in kN. P1=186kN, P2=107 kN and x = 7.9 m. Write numerical value only and in 2 decimal places
Assuming that P = 48 000 lb and that it may be applied at any joint onthe line FJ, determine the location of P that would cause (a) maximum tension inmember HI; (b) maximum compression in member CI; and (c) maximum tensionin member CI. Also determine the magnitude of the indicated force in each case
Determine the force in members BC, CD, and CG, if W = 8 kN. Specify whether each member is in tension or compression.
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 16 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 × 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at midpoint.