.A factory takes a load of 2400 kVA at 0.6 pf lagging. A synchronous motor having an input rating of 1500 kVA is to be installed to carry an additional load 1200 kW (Output) and also to improve the power factor. Assuming a motor efficiency of 92.4%, Calculate the over-all kVA load

.A factory takes a load of 2400 kVA at 0.6 pf lagging. A synchronous motor having an input rating of 1500 kVA is to be installed to carry an additional load 1200 kW (Output) and also to improve the power factor. Assuming a motor efficiency of 92.4%, Calculate the over-all kVA load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.21P: An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor...

See similar textbooks

Related questions

Q: Q6] Give one example for each of the followings: 1-Signal processor 2- Data presentation. 3- Data…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: The received power and noise power measured at a receiver is 0.5 mW and 150 nW, respectively.…

Q: If Vab = 210 Vrms in a balanced Y-connected three-phase generator, find the magnitude of the phase-b…

A: (Q10)Solution:- Given:- (1) Vab =210 Vrms (2)Y -connected three-phase generator

Q: help me calculate the Rn, In or Isc, and current at Zc using NORTON’S THEOREM

A: The given circuit is as shown below,

Q: Given a Voltage Feedback CE amplifier with the following data: RF= 5 KQ, RE = 200 Q, Rc = 1 kQ, Vcc=…

A: Given: A voltage feedback CE amplifier has the following data: RF=5 kΩRE=200 ΩRC=1 kΩVCC=12…

Q: 6. a. Write the mesh equations for the network of Fig. 8.123 using the general approach. b. Using…

A: perform mesh analysis part (A) The Mesh equations are…

Q: TOTAL CAPACITANCE Z

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Za= 10 ohms Zb = -j5 ohms Zc = 4+j4 ohms Zd = 6-j8 ohms Ze = 5 ohms Ea = 10 angle 0 Eb = 5 angle 0…

Q: stion 20 Compute for the current is in the circuit shown below. O 1.0672 A O 1.0745 A O 1.0724 A O…

A: We need to find out the current for given circuit

Q: Laplace Q1: For the circuit shown below; find i(t) for t > 0 3A -0 29 2u(1) V(1) ↓i(1) ΤΗ

A: In this question we need to find a current i(t) for t>0 by using Laplace transform

Q: 2 A C3 C₁ C₂ C3 = 2mF C4 = Cs = G6 = 4MF VAB = 10V A) CTOTAL - B) Q TOTAL M VIORAL V₂4 = C₂ = Cs Y|…

A: According to bartleby expert guidelines I need to answer only two sub parts . I have answered the…

Q: 1. A simple half wave rectifier consists of a diode and load. If the internal resistance of the…

Q: Given: 120V, 60H₂, 30, 6 Pole , Y-connected IM R₁ = 0.08₁ X₁ = 0.3 S = 0,03, XM = 6.33 R2 = 0.07, X₂…

Q: For the Circuit show below, D1, D2 and D3 are identical having VD-0.7V. Find the currents I1, I2,…

Q: For the circuit shown above, what is the magnitude of the line c current? Assume that ZY = 9 + j 6…

Q: 4.20 Calculate the inductive reactance in N/km of a bundled 500-kV, 60-Hz, three-phase completely…

A: Given A overhead line with parameters, we need to determine the inductive reactance. Please find…

Q: (1) Please don't write on a paper. I can't understand handwritten well. 1. DETERMINE THE MAGNETIC…

A: Magnetic field strength: It is a force that is applied to the moving electric charge. This is…

Q: 1. Discuss the difference between Passive and Active Components? Give examples

A: Given We need to enumerate the difference between passive and active components. Please find the…

Q: Suppose a wave whose expression is given as y(t) = Asin (2nFt), where y is the vertical displacement…

A: This question belongs to circuit theory . It is based on the concept of sinusoidal analysis . Have a…

Q: 8. A 4.7M ohms resistor is in series with a 0.15 farad capacitor. The combination is across a 12 V…

Q: Analog Electronic (Field-Effect Transistors) a) Name the transistor used and plot the transfer…

A: Here we will discuss about FET & its characteristics.

Q: A certain amateur radio station is tuned at 200 kHz with an image frequency at 460 kHz. Determine…

Q: V- V₂ 33 ΚΩ 10 ΚΩ 330 ΚΩ +9V -9V V

Q: Q2 A series RLC bandrejec calculate the values of L an

Q: Simplify the following Boolean functions by tracing it on a K Map, grouping of blocks the best…

Q: If Vab = 221 Vrms in a balanced Y-connected three-phase generator, find the magnitude of the phase-a…

Q: a) Primary transmission Secondary transmission b) c) Primary distribution d) Secondary distribution

A: Primary transmission : In primary transmission voltage is transmitted at 132 KV to the transformer…

Q: A 230-V, 50-Hz,40 HP induction motor has power factor of 0.8 (lagging). Three A-connected capacitors…

Q: Find the following:

Q: ii) Using Gauss' Law derive the equation for the capacitance of a spherical capacitor. iii) If a…

Q: ANALOG ELECTRONIC (FET) Determine the operating point of the amplifier by finding I(DQ) and V(GSQ)…

A: The required parameters can be calculated by using DC analysis of the amplifier circuit.

Q: Find the Thévenin equivalent circuit with respect to the terminals a,b for the circuit shown. 72 V…

Q: A 3-phase, 400-V, Y-connected synchronous motor has an equivalent reactance of 1 ohm per phase. The…

Q: Q4: For the unity feedback system below: k G(s) = - (s+5)(s+20) (s +50) 1. Draw the Bode…

Q: M 10 ohms 10 ohms M 10 ohms O b 10 ohms 10 ohms a 10 ohms M 10 ohms 10 ohms 10 ohms

Q: (a) Point charges of 1 nC and 2 nC are located at (0, 0, 0) and (1, 1, 1), respectively, in free…

Q: Given the amplifier circuit below, solve for the following, Zin, Zo, Avs, AIS 18V +V Q 1k C1 119 200…

A: Given the circuit, as shown below: We need to find Zin , Zo , Avs , AIs

Q: : Find the transmission parameters !

Q: Design a microgrid for a community considering the the natural hinderances

A: Communities across the country are becoming increasingly interested in greater spatial control over…

Q: Q10- Design Colpitts oscillator to generate sine wave with frequency equal to 3 KHz, with gains…

Q: A 12-bit ADC is connected to the positive reference voltage of 1.5V and negative reference voltage…

Q: 1. Find the Thevenin and Norton equivalent circuit with respect to terminal A and B. 201 40 Ω 40 Ω Μ…

Q: Q2. Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Rc 1.0 KO RB Vcc 20 KQ Bpc =50…

Q: Two resistors, 18 ohms and 24 ohms, are to be connected in parallel across the certain voltage…

Q: In a balanced three-phase Y-Y system, the source is an abc sequence of voltages and Vab = 476∠3°…

Q: Under some conditions, it is possible to approximate the effects of ferromagnetic materials by…

A: Given Few parameters of cylindrical wire,we need to determine magnetic field, magnetic field…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: Thermal power plant: The plant that produces electrical energy by the use of the coal as a…

Q: A long solid conductor with diameter 2 cm carries a current of 32 A uniformly over its cr section.…

A: In this question we will find magnetic field H at given distance due to long solid conductor....

Q: Q2 (i) Consider the circuit shown in Fig. 2.1. R = 100 Vi = Vsin t (a) (b) (c) (d) (e) C = 50 µF Vo…

A: As per the guidelines of Bartleby we supposed to answer first three subpart only for solution of…

Q: No. 3: etermine the power absorbed by each of the resistors in the circuit shown in g.(3). 3 A 12 V…

Concept explainers

Synchronous Motor

The synchronous motor is an AC electric type motor where at a steady-state the shaft rotation is synchronized with the supply current variable-frequency. To an integral number of AC cycles, the rotation period is exactly equal. The stator of the motor in the synchronous motor contains multi-phase AC electromagnets due to which a magnetic field is created that rotates in time with the oscillation of the line current. The rotor contains a permanent magnet and the rotor rotates in synchronization with the stator field at the same rate and provides the second synchronized magnetic field which is rotating in nature as a result. When the synchronous motor is supplied with independently excited multi-phase AC electromagnets on both the rotor and the stator, it is termed as a doubly-fed machine. The most widely used AC-type motors are the synchronous AC motor and the induction AC motors.

Question

15.A factory takes a load of 2400 kVA at 0.6 pf lagging. A synchronous motor having an input rating of 1500 kVA is to be installed to carry an additional load 1200 kW (Output) and also to improve the power factor. Assuming a motor efficiency of 92.4%, Calculate the over-all kVA load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An industrial load uses 310-kVA at 0.6 pf lagging. A synchronous motor is added to the system to improve the power factor. The power required by the synchronous motor is 31-kW. (i)What is the complex power required by the load (P + jQ)[kVA] If the motor is added to the load to bring the power factor up to 0.9 pf lagging, then: (ii)What is the complex power now required by the load (at the new pf) (P+ jQ)[kVA] (iii)This means that the motor has a reactive power of (-Qm)[kVAR] and is operating at: (iv) a power factor of:
Some parameters are given related to your student ID numbers. These are:V1 = XXX V (first 3 numbers, e.g. 170 V (RMS)) f1 = XXX Hz (assume that your last number is ‘y’, then f1 = (y+1)*10 Hz, e.g. if y=2 then f1=(2+1)*10=30Hz)1) A single-phase load has an active power of P = 2 kW at V1 V @f1Hz and the power factor is cosφ = 0.75. This motor iscompensated to cosφ = 0.85 using a parallel capacitor (the load is modelled as series RL). Determine:a. Reactive power and apparent power before compensation using power factorb. Current before compensationc. R, XL and L values of the loadd. Reactive power and apparent power after compensatione. Find the reactive power difference between compensated and uncompensated status (which will give thecapacitor power) and calculate XC and C using the power difference valuef. Simulate the uncompensated and compensated circuits. Plot voltage and current on components andcalculate the phase shift of the signals from Ving. Plot Vin and Iin comparison for…
: A single phase motor operating off a 400V, 50Hz supply is developing 10KW with an efficiency of 84% and a power factor (p.f) of 0.7 lagging. Calculate; The input apparent power; The active and reactive components of the current; The reactive power (in kilovars).
A generating station has a connected load of 100 MW and a maximum demand of 60 MW. The number of units produced per year is 210 × 10^6, then find (1) Demand factor (2) Load factor.
A 15kVA, 440V, single-phase alternator draws a field current of 5A at rated load. With the same field current, the open circuit emf and short-circuit current are 100V and 80A respectively. The ohmic resistance of the armature between terminals is 0.12 ohm. The ratio of effective to ohmic resistance maybe taken as 1.1. Determine the voltage regulation (in %) when the load is purely resistive.
The load at a certain factory consists of the following:10 kW, pf = 0.6 lagging15 kW, rf = 0.5 lagging25 kVA, pf = 0.75 lagging15 kVAR, pf = 0.8 lagging22 kW5 kVAR, pure inductance1. The power factor is to be corrected to 0.95 lagging. If a synchronous motor is to be used instead, determine the real power rating of this motor if its power factor is 0.6 leading. Ans = 18.257 2. The power factor is to be corrected to 0.95 lagging. If resistive heating units were used instead, determine the real power rating of these devices. Ans = 92.3222 3. The power factor is to be corrected to 0.95 lagging. The power factor is to be corrected to 0.95 lagging. Determine the kVAR rating of pure capacitors needed to accomplish this. Ans = 30.3447
2) The net inlet to a factory powered by a 2300 volt infinite busis measured as 765 A, for a lag 0.92 power factor. although mostloads is inductive, the input power factor has been improved by installing asynchronous capacitor operating at its nominal value of 1000 KVA. Determine the factor oforiginal factory power.
The average input to a manufacturing plant is 3.000 KVA at a power factor of 0.72 lagging. A synchronous motor having an input of 1300 KVA is then installed delivers a load of 600 hp at an efficiency of 89.5 per cent. Calculate the over-all plant power factor.
Electromechanical energy conversion (One AC induction motor and one AC synchronous motor were operated connected to an infinite bus of 600V. Power factor of the induction motor is 0,7 (lagging) and consumes 400 W from the bus. Synchronous motor consumes 300 W from the bus. If the power factor of the synchronous motor is 0,9 (lagging) find the line current from the bus, for the total of two motors (IL total 1) of the line that connects the motors with the bus and find the total appearent power (SL total 1) of the motors consumed from the bus. When the induction motor has the same conditions, if the power factor of the synchronous motor is 0,9 (leading) find the line current from the bus, for the total of two motors (IL total 2) of the line that connects the motors with the bus and find the total appearent power (SL total 2) of the motors consumed from the bus.
1-Alternators can be overloaded by 10 percentage for 10-15 minutes, this a. Steady state voltage stability will get affected b. may reduce the stability limit c. may disturb Nose point d. may lose Angular stability 2-Often, the network is referred as an infinite bus when a change in input mechanical power or in field excitation to the unit does not cause an appreciable change in a. system frequency or terminal voltage b. system frequency alone c. system frequency and terminal voltage d. Total production cost
A 50kVA, 550V single phase alternator draws a field current 10A at rated load. With the same field current, the open circuit emf and shirt circuit current are 300V and 150A. The ohmic resistance of the armature between terminals is 0.18Ω. The ratio of effective to ohmic resistance may be taken as 1.5. Determine the terminal voltage at 0.8 pf factor lagging. Use two decimal places.
A three-phase, 11kV, star-connected alternator delivers a current of 80A at (a)0.85 pf leading, (b) unity power factor, (c)0.7 power factor lagging. Full-load current of 80A is produced on short circuit by a field excitation of 2.9A. An emf of 400V per phase is produced on open circuit by the same excitation. The effective armature resistance is 0.85 ohm per phase. Determine the voltage regulation in each case.