0) The slab shown below is loaded with D = 8 kN/m² and L= 4 kN/m². All beams are mm in width and 600 mm in depth and all columns are square with side length of mm. If the slab is 200 mm thick and is reinforced with 10 mm diameter bars in directions, then: (a)Calculate the design moment of the slab at A. (b)Calculate the uniformly distributed load on heam B1

0) The slab shown below is loaded with D = 8 kN/m² and L= 4 kN/m². All beams are mm in width and 600 mm in depth and all columns are square with side length of mm. If the slab is 200 mm thick and is reinforced with 10 mm diameter bars in directions, then: (a)Calculate the design moment of the slab at A. (b)Calculate the uniformly distributed load on heam B1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a 7-story buildings with a total plan area BxL. In which B=125ft and L=60ft . The average weight of each floor and roof are 95 Ib/ft and 75 lb/ft?, respectively. The 84 ft-tall building is located in a seismic region with SDs =1.6 g and SD1 =0.5g for a building supported on rock, where g is the gravitational acceleration. The structure of the building consists of steel moment frames (all joints are rigid) that have an R value of 8. The importance factor I=1.0 Determine the total design seismic force (kips) acting at the base of the building ( seismic base shear in kips). ***the answer was between 339.5 and 342.5*** but I don’t understand how . Handwritten work is preferred
The section of a concrete gravity dam is shown in the figure. The depth of the upstream side is 6.0 m. Neglect the hydrostatic uplift and use unit weight concrete equal to 24 kN/m3. The coefficient of friction between the base of the dam and foundation is 0.4. Determine the following: (a) factor of safety against sliding (b) factor of safety against overturning (c)the overturning moment acting against the dam in KN-m.
An L = 38-ft-long soldier beam is used as a key component of an earth retention system at an excavation site. The soldier beam is subjected to a soil loading that is linearly distributed from wA = 430 lb/ft to wC = 270 lb/ft, as shown. The soldier beam can be idealized as a cantilever with a fixed support at A. Added support is supplied by a tieback anchor at B, which exerts a force of P = 5000 lb on the soldier beam at a = 29 ft. Determine the horizontal deflection of the soldier beam at point C. Assume EI = 3.8 × 108 lb·in.2. Deflection is positive to the left.
A simply-supported beam, 9 m in length, pin at A, roller at B and midspan at C, is subjected to a uniform load of 20 kN/m applied at the beam's middle third. a. Determine the tangential deviation of C wrt B. b. Determine the tangential deviation of A wrt B.
Given the ff. data of dynamic lateral force procedure for buildings:Period of vibration: T = 0.8 secSpectral velocity, Sv = 0.15 m/secK = 15 158 kN/mmTotal W = 2400 kN Give the maximum relative displacement,the value of spectral acceleration,value of the lateral force of the tank in kN,the value of the maximum base shear in kN.
A given frame is subjected to loads as shown and analysed using Modified Slope Deflection Method. (a)what is the moment KNm at D? (b)what is the maximum positive moment KNm for member BC? (c)what is the horizontal reaction KN at A?
A 5-m propped beam carries a uniformly distributed load equal to 45 kN/m applied throughout the beam. If the reaction at the roller is 84.375 kN, what is the maximum flexural shear stress if the beam has a rectangular cross-section with b = 300 mm and h = 600 mm? (in MPa)
Determine the force P needed to pull the 50-kg roller over the smooth step. Take θ = 30°.
In the built-up box beam shown below, if a vertical shear force is applied, what value of Q, the first moment of area, should be used in determining the shear stress and/or shear flow at point A? Give your answer in m3m3.
The section of the masonry dam is shown in Figure3a. If the uplift pressure varies uniformly from fullhydrostatic at the heel to full hydrostatic at the toe,but acts only over 2/3 of the area of the base, find(a) the location of the resultant; (b) the factor ofsafety against overturning; and (c) the factor ofsafety against sliding if the coefficient of frictionbetween base and foundation is 0.60. Unit weight of concrete and masonry is 23.54 kN/m3for all the problems NOTE: CLEAR HANDWRITTEN SOLUTION
Calculate the width of the concrete wall that is necessary to prevent the wall from sliding and the horizontal reaction acting on the system, Rx. The unit weight of the concrete is 23.6 kN/m^3 and the coefficient of friction between the base of the wall and the foundation soil is 0.42. Use 1.5 as the factor of safety against sliding. Will it also be safe from over turning?
A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.