04:4 a) a data rate of 30 MBit/second through this channel. According to the channel capacity theorem for continuous channels, what is the minimum required E, IN (Bit energy-to-noise power spectral density) to achieve the above requirement with zero-eror. A Gaussian channel has a bandwidth of 5 MHz. It is desired to send

04:4 a) a data rate of 30 MBit/second through this channel. According to the channel capacity theorem for continuous channels, what is the minimum required E, IN (Bit energy-to-noise power spectral density) to achieve the above requirement with zero-eror. A Gaussian channel has a bandwidth of 5 MHz. It is desired to send

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4.27 Consider a baseband M-ary system using M discrete a mplitude levels. The receiver mofiﬂl is as shown in Figure P4.27, the operation of which is governed by the following assumptions: Problems 305 (a) The signal component in the received wave is x £ m(t) = ; a, smc(T n) where 1/T is the signaling rate in bauds. (b) The amplitude levels are a, = *A/2, +34/2, ..., =(M — 1)A/2 if M is even, and 4, =0, *4,...,=(M— 1)A/2if Mis odd, * (c) The M levels ate equiprobable, and the symbols tranismitted in adjacent time slots are statistically independent. (d) The channel noise w(t) is white and Gaussian with zero mean and power spectral density No/2. () The low-pass filter is ideal with bandwidth B = 1/2T. (f) The threshold levels used in the decision device are 0, A4, ..., (M — 2)A/2 if M is even, and *4/2, *3A/2, ..., (M — 2)A/2 if M is odd. The average probability of symbol error in this system is defined by where o is the standard deviation of the noise at the input of the decision…
4. We measure the performance of a telephone line (4 KHz of bandwidth). Whenthe signal is 10 V, the noise is 5 mV. What is the maximum data rate supported bythis telephone line?
Explain in detail the essential things that happen to the modulating signal before transmission. Discuss all types or kinds available if necessary. Note that without these essential systems, transmission will not be able to be sent to yield the needed result.
i) To mitigate impairments in communication system there is the need to discuss how Shannon defines and measures information. As communicationengineer you are required to give your submission on the above.ii) Present your point view on mutual information, how channel capacity isassumed, and declare the Shannon capacity formula for the additive white Gaussian noise channel
Q3 (i) What do you mean by baseband transmission of a digital signal ? What are the possible types of connection of devices in a topology for communication?
what is the realistic channel capacity of a communication channel of 25KHZ that has 20db signal to noise ratio?
(b) In which encoding scheme Nyquist theorem is used and Why? Explain complete procedure of that Encoding scheme with example with the advantages and Disadvantages of this theorem.
Derive Parseval’s relation for the DFT.
What is binning and what is it used for? A. This is the approach of separating the obtained fluorescent light to several detectors at once, which increases the sampling frequency. B. It is a matter of combining the load of several pixels as if it came from only one pixel, which increases the sensitivity and speed of detection but reduces the spatial resolution. C. It is a strategy to increase the gain of the camera to get a stronger signal in low light conditions, even if it means getting more saturated pixels. D. This is the use of a detector that is always on, so that photons emitted under very low fluorescence conditions are detected more quickly and more effectively.
A noiseless channel of bandwidth B=50 kHz. Determine: (a) The value of M for transmitting the QAM symbols in 800 kbps bit rate. (b) Determine the bandwidth efficiency for step (a). Discuss the result.
Consider an industrial network application where there is one control unit (PLC) connected using half duplex connection with 20 other sensor and actuator devices having a bandwidth of at least 100Kbps located at the distance of around 2000 feet apart. Choose a most suitable fieldbus protocol and serial communication protocol along with wiring, cable, topology and any other requirement details to connect all these devices efficiently.
From the Root locus plot obtained from the system below, ANALYSIS and DISCUSS the Root locus plot obtained with PID controller