(b)As thebarometric pressure increases, the boiling point of a liquid _________

Q: What are the types boiling occur in evaporator? Define them

A: Define : the type of boiling occur in evaporator

Q: describe the five types of reservoirs and draw pressure-temperature phase diagram of each fluid

A: Types of Reservoirs : Single phase gas reservoir: It primary consist of recovery mechanism of…

Q: Question 25 Which of the following statements about the pressure of a gas is true? None of these are…

A: Write the equation for the absolute pressure. PA=PG+PAtm Here, The absolute pressure is "PA" The…

Q: In ITS-90, which temperature scale is considered in four ranges?

A: Out of four temperature scales, Kelvin (K) is considered for ITS-90. ITS stands for the…

Q: ) in multipi System, Vapor is formed in firsh effect by s a) Boiling mechanism D) Pressure drop…

A: In multiple effect evaporation system, the vapour is formed in first effect by boiling mechanism.

Q: A liquid is boiling in a airtight vessel. Using an exhaust tube the vapour is pumped out at a faster…

A: As the vapour is pumped out so the temperature will go down but as the pressure will remain at the…

Q: Which of the following gasifiers has the Lowest thermal output?

A: Answer is Downdraft

Q: What is the final gas pressure?

A: Final gas pressure need to find.

Q: For what purpose is  the secant formula used?

A: Secant formula is used to calculate buckling load in columns. In Euler formula we assume that the…

Q: Give the formula of calculating heating value; DULONG’S FORMULA , ASME FORMULA, BUREAU OF STANDARD…

A: Given Heating Value To find Mathematical Formula DULONG’S ASME BUREAU OF STANDARD FORMULA

Q: the maximum surface temperature on the circuit board (°C)?

A: Given: Cp=5193 J/kg°Cν=1.233×10-4 m2/sρ=0.1635 kg/mPr=0.669k=0.1565 W/m°CChannel dimension =0.46…

Q: What are the advantages of Contact condensing systems?

A: In contact condensing systems, the direct contact between the two mediums takes place. The…

Q: ent, of an alloy that consists

A: Atomic% of Cu =5% Atomic% of Pt= 95 % Required Wt% of above elements in alloys

Q: aturated vapor.

A: Kindly refer attached files.

Q: Discuss crank case Ventilation, implosion and Explosion

A: basically a crankcase can be defined as a housing for the crankshaft in a reciprocating internal…

Q: A- What is meant by the term superheat?.

A: Solution:   Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: What affects the evaporation rate?

A:

Q: Explain in detail with relevant sketch, the working of high pressure boiler.

A: The high pressure boiler generate electricity by turning water into steam using thermal energy in…

Q: Exceptional gases are an example of type of lubricant. Semi-solid Gaseous O Liquid O Solid

A: Lubrication: The process of applying lubricants to the machine parts to decrease the heat generated…

Q: kindly differentiate the canning methods of process in boiling water bath and using autoclave with…

A: Canning is the process in which foods are placed in cans and jars and heating them to a specified…

Q: 1) For same cooling media temperature, If ,highest condensation pressure is obtained. Select one: a.…

A: According to Bartleyby's policy we can answer only one question at a time so if you want the answers…

Q: In general, steel produced by the Basic Oxygen Furnace is of a better quality than the one produced…

A: Basic Oxygen Furnace It is a pear-shaped structure with a closed bottom and an open top. It is used…

Q: The conclusion of Inverse Square Law for Heat

A:

Q: What is chilled and condenser treatment process?

A: A chiller is a mechanical system used for the purpose of refrigeration in industries. It helps in…

Q: How is the selection of coolant done in condensing systems?

A: Coolant : Coolant is a substance which is used to remove or extract the heat from the parts which is…

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: 15. Describe a superheated vapor.

A: Here, point s represent superheated steam.

Q: The name for the process in which water vapor changes back into a liquid is deposition sublimation…

A:

Q: What caused the vibration at the bottom of the calorimeter as the steam is allowed to enter the cold…

A: Given Calorimeter To find Vibration reason

Q: temperature of the black body?

A: Given; Peak wavelength of a black body emitted is;  λ1=1.75 μmBlack body emitted at a temperature;…

Q: 0m and diameten

A:

Q: Solidification is the process of changing the state of the material from powder to solid liquid to…

A: For changing the phase transformation, there are various processes such as, - Condensation Process -…

Q: boiling point

A: 446deg.c-answer

Q: 4. Is a fire hydrant more likely to be cast or forged? Why?

A: Is a fire hydrant more likely to be casted or forged? The fire Hydrant are more likely to be Casted,…

Q: Define the low pressures (below the triplepoint value), solids evaporate without melting first…

A: At the triple point of a substance, all the phases exist together in equilibrium with each other. At…

Q: Boiling

A: given:T1=1100XT2=4500X

Q: industrial application of fire tube and water tube boiler

A: Fire tube boilers: It is the type of boilers in which hot gases are passed through the tubes which…

Q: State the standard conditions for water to boil at 212°F.

A: In this problem, it is asking about the standard conditions for water to boil at 212°F.

Q: Fighter planes fly at 35,000 ft elevation. What must be the muzzle

A: Given data: The elevation of planes, h=35000 ft. The final velocity of the muzzle is, v=0. Write…

Q: Where do you see condensation in the setup?

A:

Q: Identify if the following phase is saturated, subcooled, superheated, or wet-mixture. Temp Pressure…

A: Given Data P=16. MPa T=335°C

Q: What is the critical temperature for N2? In R

A: The critical temperature of N2 is −146.9 °C (126.2 K).