1-106. The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of 6 kN. Determine the average normal and shear stress acting on the plane through section a-a. Show the results on a differential volume element located on the plane. a 30° 6 kN 150 mm a

1-106. The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of 6 kN. Determine the average normal and shear stress acting on the plane through section a-a. Show the results on a differential volume element located on the plane. a 30° 6 kN 150 mm a

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: hen someone says that the precision of data has been defined, what does that mea

A: Surveying plays an important role in a variety of fields, such as construction, engineering, land…

Q: Using the cut method, draw the shear and moment diagrams for the beam, and calculate the shear and…

A: Given:To find:Shear and moment equation as a function of x for each segmentShear and moment diagram

Q: A centrifugal pump delivers water against the net head of 14.5 metres and at a design speed of 1000…

Q: Given the following information for a simple spiraled curve I = 18°00'00" Da = 7°00'00" Ls = 600…

Q: If the unfactored shear actions due to dead and live loads are VG = 300 kN and VQ = 80 kN (including…

A: Dead loads, VG = 300 kN Live loads, VQ = 80 kNTo find:The nominal shear stress (vn) acting on the…

Q: The beam shown in Figure 1 has lateral support at a, b, c, and d. Compute Ch for segment b-c. (a)…

A: Formula required:Cb =where,Mmax = Maximum bending moment magnitude in BCMA = BM at quarter point of…

Q: In (Figure 1), the tension developed in cables AB and AC cannot exceed 330 lb. Figure 5.5 ft J11 2…

A: Tension developed in AB and AC cant exceed 330 lb .

Q: .Draw the correct load distribution on the framing plan, 2. Solve for the reactions and shear and…

A: Please note that only one of the beam will be analyzed.

Q: Determine the required cross-sectional areas of all the remaining members of the given truss shown,…

Q: The data in the table below is for a closed-polygon traverse. Balance the traverses by coordinates…

A: Preliminary coordinates are XA= 9500 YB = 11000

Q: The theoretical and measured unit weight of mix is a Marshall specimen prepared for bituminous…

A: Theoretical unit weight Gt= 2.4 g/cm3Measured unit weight Gm = 2.2 g/cm3Bitumen content Wb =…

Q: Based on the following figure determine the coordinates (on the x, y axes) of the centroid of the…

Q: For the shaded area shown below: a) Determine the moments of inertia with respect to the x and y…

A: Consider the given region into 2ma.) The moment of inertia with respect to 'x' axis.

Q: Draw the projection of a regular hexagon of 30 mm side, having one of its sides in the HP and…

A: Hexagon of side 30mmInvlination 60 to the VP and 45 to the HP

Q: (b) wim d O ✓ Structures e) through f) have truss-type members. Diagonals are not connected where…

A: We have to determine the if the structure is statically determinate or not.We have to solve d, e and…

Q: A Pitot tube (coefficient = 1.0) is used to measure the velocity of air of mass density 1.2 kg/m2…

Q: The underpass sight distance design criteria only applies to crest vertical curves O True O False

Q: A plain sedimentation tank with a length of 20 m, width of 10 m and a depth of 3 m is used in a…

A: A plain sedimentation tank-Water to be treated per day Q=4 MLD,

Q: Problem 2. A simply supported beam is subjected to a uniform service dead load of 1.5 kips/ft…

A: Service dead load = 1.5 kips/ftService live load = 2.2 kips/ftConcentrated service dead load = 50…

Q: The old H. A. Blooms wastewater treatment plant discharges secondary effluent to a lake that is…

A: Given;The old H.A Blooms wastewater treatment plant discharges secondary effluent to a lake that is…

Q: An unsymmetrical flexural member consists of a %x14 in. top flange, a ¾×10 in. bottom flange, and a…

A: given:A572 Grade 50 steelLet us assume, Yield strength (Fy) = 345 MPa (50 ksi)Moment of inertia (I)…

Q: 3- Estimate the Curve Number for all three AMC conditions for a basin with the following data: Soil…

A: Land use data of a watershed with 60% Farm, 15% seeded and 25% fair pasture land.

Q: A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50mm and initial…

Q: The beam-column in the figure is a member of a braced frame. Use LRFD and determine whether this…

Q: For each structure shown, compute the reactions and draw shear and bending moment diagrams. Indicate…

A: Note:- Since you have posted multiple questions, we will provide the solution only to the first…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: ###Determination of members forces of truss using method of joint ###

Q: j: A dam shown in Figure 1 retains 10 m of water. A sheet pile wall (cutoff curtain) on the upstream…

A: A seepage path and sheet pile is shown in the above figure. We have to find out the followings:…

Q: An inclined manometer can measure the pressure difference of 200 Pa. The inclined manometer has a…

A: An inclined manometer can measure the pressure difference of 200 Pa.The inclined manometer has a…

Q: 8. A horizontal beam of unit length under load w(x) satisfies the system: y" = M, M" = w(x), x = (0,…

Q: Question 4 Members of the truss shown consist of sections of aluminum pipes with the cross-sectional…

Q: Using Moment Distribution Method, determine all reactions at supports also, determine shear and…

Q: (4)+The-sandbag-in-the-figure-below-weighs-50-lb.--The-coefficient-of-friction-between-the-rope-and-…

Q: For the splice connection shown in the figure, Compute the design strength based on shear and…

Q: What is the coefficient of side friction for a horizontal curve with a design speed of 70 mph?

Q: Osec The hydrostatic represented σij = stress for the state of stress MPa by ¤¡j given below is 100…

A: A state of stress given as shown-Now,From the stress tensor, we get-To Find-The value of hydrostatic…

Q: The temperature of the cylindrical rod is heated to 45°C which is fixed in between A and C rigid…

Q: What design changes to either the task or equipment could you make that would either compensate for…

A: When it comes to compensating for limitations in human senses or capitalizing on other human…

Q: geomaterial. Case history- Housing Project established in 2013 Location Dubai, UAE Geomaterial (0-6…

A: 1.rapid impact compaction is not a good selection because it is not an accurate on and it is not…

Q: B) Calculate the amount of einforcement for the concrete asement of water tank shown using CI and BS…

A: Depth of the basement, H = 700 mmTake clear cover as 50 mmTo find:The amount of reinforcement should…

Q: 64 A pelton wheel works under a head of 400 m. Frictional loss through the pipe flow is limited to…

A: A Pelton wheel turbine-Head of wheel = 400 mLimitation of frictional loss = 10%The coefficient of…

Q: A closed cylindrical tank 2 m. diameter and 4m depth with axis vertical contains 3m. depth of water.…

Q: I need help with part b). Thank you,

A: Determine the force in the member U3L3, L3U4 and L3U5.

Q: The total estimated duration of the mass excavation activities in an office building project is 40…

A: Expected time of completion = 40 daysTime completed = 18 daysActual excavated volume = 8400 (cubic…

Q: n a material the principal stresses are 60 MN/m², 48 MN/m² and -36 MN/m². When the values of E = 200…

A: In a material the principal stresses are,E = 200 GN/m2To find:Total strain energy per unit volume

Q: The frame is made up of members ACE, BCD and DE. The frame is pin-supported at A and…

A: Consider Moment equilibrium at A500*3 =Bx*6Bx = 250 N

Q: Classify: A soil characterized by the following description: “78 % fine to coarse, hard, subrounded…

Q: A 490 ft equal-tangent sag curve is currently designed for 50 mph. A CE 321 student thinks that…

Q: Example 1.1 Determine the stress in each section of the bar shown in Fig. 1.19 when subjected to an…

A: As per Bartleby's guidelines we are supposed to answer only first question.Kindly repost other…

Q: 1- There following data are obtained from streamflow measurement in a river cross section. Estimate…

A: distance from left corner 01234567water depth01.353.315.09.05.383.781.78flow velocity at 0.2…

Q: 10 ft А B 10 ft C 10 ft 10 ft E 10 ft D ANA J F 10 ft H G 3000 lb 3000 lb Determine the forces in…

Concept explainers

Planar Stresses

Question

1-106. The bearing pad consists of a 150 mm by 150 mm
block of aluminum that supports a compressive load of
6 kN. Determine the average normal and shear stress acting
on the plane through section a-a. Show the results on a
differential volume element located on the plane.
a
30°
6 kN
150 mm
Prob. 1-106
a

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:-

VIEW

Step 2: Normal and shear force on section a-a:-

VIEW

Step 3: Average normal stress and shear stress:-

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
Determine the largest load P that can be applied at A when θ = 55º, knowing that the average shearing stress in the 10-mm-diameter pin at B must not exceed 120 MPa and that the average bearing stress in member AB and in the bracket at B must not exceed 90 MPa.
What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.
Find the Maximum Shear andMoment.? can you solve in 20 mins?
Compute the shearing stress (MPa) in the pin at B for the member supported as shown in the figure below. The pin diameter is 20 mm Final answer should have 2 decimal places Where: L1=204 mm, L2=259mm, P=47 kN and angle =39
Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are in compression and that force is 25 kN in angle bar B and 40 kN in angle bar C, determine thefollowing: a. Number of 19 mm diameter rivets in angle bar B if the allowable bearing stress of angle baris 60 MPa. Thickness of angle bar B is 6 mm.b. Number of 19 mm diameter rivets in angle bar C if the allowable shearing stress of rivets is25 MPa. Thickness of angle bar is 5 mm.
Determine the magnitude of the pin force at C given θ = 18° and P = 57 lbs.
a) What is the distance to centroid (x）? Please enter answer in mm and to 1dp. b) For the same section, what is the distance (e) in mm from the centreline of the left-hand web to the shear centre? The shear centre is marked as the blue dot in the previous figure. c) If the section is subjected to a point load of 100kN, what is the maximum shear stress in the section (in MPa)?
A horizontal beam AB is freely supported at A and B, 8metres apart and carries uniformly distributed load of 15KN/m run (including its own weight). A clockwise moment of 160KN-M is applied at a point C, 3metres from left hand support A.using Macaulay method, calcite the beam at C if El=40×10^3KN-m^3