1- Calculate the stress at a-a and b-b sections.

Q: combined stresses for the

A:

Q: Determine stress in rod

A: Given data :   Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: F V=FU M=hF Find the principal stress at point C and D

A:

Q: 1- Calculate the stress at a-a and b-b sections.

A:

Q: Compute the maximum shearing stress at A in MPa. b. Compute the maximum shearing stress at B in…

A:

Q: 2- What is the maximum shear stress in the shaft in (MPa)?

A:

Q: Problem 1 in Fig. 1(c). Use the following formula and values for computing stresses (7 and o). Then,…

A:

Q: Find the stresss in the left rod after its lower end is attached to the support.

A:

Q: 1- Calculate the stress at a-a and b-b sections. 1.2m a -30mm + 6. R=50 kN 0.&m 20M A

A:

Q: Problem 1-3 The Cartesian components of stresses at a point are given as belou : O = 7, 0y = 6, oz =…

A: The cartesian components of stresses at a position specified in the inquiry are known to us :…

Q: the stresses at point A.

A: To find Stresses at point A

Q: Determine minimum principal stress

A: Given data : Normal stress in X direction (σX)=10 MPaNormal stress in Y direction (σY)=50 MPaShear…

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

A:

Q: cresses at A and B points according to the ven and show them on the stress element.

A:

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: Draw Mohr’s circle that describes each of the following states of stress.

A: The maximum and minimum stresses are known as the principal stresses. The angle of the plane is two…

Q: Find the stresses in A, B and C?

A:

Q: Problem 1-12 The state of stress at a point is given by : 0, = 40, %3D Oy = 50, 0; = - 70, ty = 40,…

A: The direction cosine after rotation are,        x y z x' 3/2 1/2 0 y' -1/2 3/2 0 z' 0 0 1

Q: QUESTION 4) For the given plane state stress, if the 14 MPa components at the inclined surface is…

A:

Q: For the figure shown determine the value of the maximum normal stresses, due to the change of…

A: Calculate the reaction at the left end support as follows, RL=10×250+5050+500+250+50RL=3.53 kN,…

Q: Two cables BC & BD are pull out the ship as shown in Fig. (6), if the diameter of each cable is 50…

A:

Q: Compute the normal and shear stress on a plane which is 45° inclined from vertical axis of a…

A: Given data: -  The angle of the plane with vertical axis is θ = 45o. The axial stress on the box is…

Q: Calculate the stress at a-a and b-b sections

A: FBD of AB & BC

Q: 1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

A:

Q: A rectangular block of 1200 mm? cross-section- al area is subjected to a longitudinal compres- sive…

A:

Q: a, determine stresses at an angle

A: Need to Determine the stresses

Q: střéss is proporti of shear stress is p r stress is proport

A: A Newtonian fluid is one in which the viscous stresses generated by its flow are linearly…

Q: find the average shear stress on the section of the inclined member if we were to cut it…

A:

Q: Calculate the maximum normal strain in the bar in με.

A:

Q: Calculate the maximum shear stress at that point.

A: Given that principal stresses on a point are: σ1 = 250 Mpa σ2 = -30 MPa It is required to determine…

Q: The main stress, the maximum shear stress, and the dead angle are obtained when the stress is given…

A:

Q: Determine maximum  principal stress

A: Given data: σx=10 MPaσy=50 MPaτxy=15 MPa Need to determine the maximum  principal stress.

Q: etermine the maximum shear stress in

A:

Q: the normal stress at comer A.

A:

Q: Determine state of stress at point A and B

A: Given data, The applied axial load, P = 20×103 N The applied transverse load or shear force, SF =…

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the…

A:

Q: QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and…

A:

Q: Determine the maximum tensile stress (MPa) at

A: Determine maximum tensile stress.

Q: Find the principal stress at point C and D

A: The force F causes the bending moment at point C, and at point D only shear force will be there…

Q: a) Calculate the maximum stress in the steel ring. b) Calculate the pressure exerted by the copper…

A: we are to determine the stress generated in the composite ring

Q: Compute the maximum shear stress

A:

Q: at each of these he state of stress

A:

Q: Compute maximum principal stress

A:

Q: a. Compute the maximum shearing stress at point B in MPa.  b. Compute the normal stress at point B…

A:

Q: compute the compressive stress

A:

Q: Determine stress produced

A: Given data : Force (F)=20 KNArea (A)=2 mm2

Q: 5. Distinguish clearly between direc stress and bending stress

A: Stress induced in the body due to tension or compression is called Direct Stress. For example, when…

Q: An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are…

A:

Q: QUESTION 4) For the given plane state stress, if the components at the inclined surface is known and…

A:

Q: When the stress conditions are given as shown below, calculate the vertical stress and shear stress…

A: Write the given information.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.