soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was saturated until the pores were filled and now weighs 273g. The sample was drained and weighed 236g. The sample then sat out for about 2 weeks until at equilibrium and weighed 206g. After oven drying the sample, it fi

soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was saturated until the pores were filled and now weighs 273g. The sample was drained and weighed 236g. The sample then sat out for about 2 weeks until at equilibrium and weighed 206g. After oven drying the sample, it fi

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter4: Plasticity And Structure Of Soil

Section: Chapter Questions

Problem 4.4P: Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit...

See similar textbooks

Similar questions

Results from a liquid limit test conducted on a soil are given below. a. Determine the liquid limit of the soil. b. If it is known that the PI = 6.5, what would be the plastic limit of the soil? c. Determine the liquidity index of the soil if win situ = 23.8%
A soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was saturated until the pores were filled and now weighs 273g. The sample was drained and weighed 236g. The sample then sat out for about 2 weeks until at equilibrium and weighed 206g. After oven drying the sample, it finally weighed 202g. What is the percent moisture content by mass (theta g) at field capacity %?
An undisturbed specimen of soil has a volume of 300 cm3 and weighs 498 g. After over drying for 24 hours, its weight is reduced to 456 g. Assume G= 2.70 . Determine the degree of saturation in percent. a. 9.21 b. 31.9 c. 43.8 d. 78
1. A moist soil sample weighing 0.20 kg having a volume of 200 cm3 and dry unit weight of 16 kN/ m . After mixing water of 65 g, compute the moisture content of the soil.
A large soil sample obtained from a borrow pit has a wet mass of 26.50 kg. The in-place volume occupied by the sample is 0.013 m3. A small portion of the sample is used to determine the water content; the wet mass is 135 g, and after drying in an oven, the mass is 117 g. Determine the soil’s water content. Determine the soil wet and dry density for conditions at the borrow pit.
A sample of 1346 grams of soil was taken from a 792 cu.cm test hole. It was then oven-dried and weighed 1076 grams. After saturating it with water, it weighed 14622 grams. What is the degree of saturation of the soil sample, in percent? What is the porosity of the soil sample?
A sample of soil taken from a borrow pit has a wet mass of 14.56 kg. Completely dried, the soil dry mass is 11.78 kg. Determine the water content of this soil.
A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of the dry soil pat was found to be 48.76 g. Given G= 2.68. Determine the saturated density in g/cc.
The hydraulic conductivity of a soil sample (3.4 x 10-4 cm/s) has been determined via a permeability test. The water temperature was 28°C at the time of experiment. What is the hydraulic conductivity of the sample at the standard temperature of 20°C?
A soil sample has a volume of 29cm^3 and a mass of 45.5 g in its natural state in the field. After drying the mass of the sample reduced to 32g. if specific gravity of solids is 2.66. find a) water content b)Vs, Va, Vw c)void ratio d) Vw in 1m3 if the soil was fully saturated
A 50 cm³ sample of moist soil has an initial weight of 85 g and after oven-drying a weight of 60 kg. Specific gravity of soil is 2.70. 1. Determine the porosity 2. Determine the degree of saturation. 3. Determine the mass of water to be removed to reduce the sample to 50% saturation.
The following are the observed lab values for determining the maximum dry unit weight of the soil. (See table below) Determine the optimum moisture content in percent (3 decimals) Determine the maximum dry unit weight, in kN/m3 (round off to the nearest 10th) How much water (in kg) must be added per m3 of soil to achieve maximum dry unit weight if initially the moisture content of the in-situ soil before testing was 6%?