1. (a) A solution of NaCl is prepared by dissolving 0.0056 g NaCl with enough H2O in a volumetric flask to yield a final volume of 10 mL. Assuming a standard (0.1 mg) analytical balance and class A glassware is employed, calculate the concentration of the solution (M) and its corresponding error. The atomic weights of Na and Cl are 22.98976928(2) and 34.45(1), respectively (the number in parentheses indicating the error in the last digit). (b) What would the error be if a 1mL transfer pipet was employed (10x) rather than the 10 mL volumetric flask?

1. (a) A solution of NaCl is prepared by dissolving 0.0056 g NaCl with enough H2O in a volumetric flask to yield a final volume of 10 mL. Assuming a standard (0.1 mg) analytical balance and class A glassware is employed, calculate the concentration of the solution (M) and its corresponding error. The atomic weights of Na and Cl are 22.98976928(2) and 34.45(1), respectively (the number in parentheses indicating the error in the last digit). (b) What would the error be if a 1mL transfer pipet was employed (10x) rather than the 10 mL volumetric flask?

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter17: Electrochemistry

Section: Chapter Questions

Problem 80AP

See similar textbooks

Similar questions

A stock solution of potassium permanganate (KMn04) was prepared by dissolving 13.0g KMn04 with DI in a 100ml volumetric flask and diluting to the calibration mark. Determine the molarity of the solution.
An impure sample of calcium carbonate with a mass of 7.95 g was reacted with 50.00 cm3 of 1.00 mol dm hydrochloric acid (an excess). The resulling solution was transferred to a volumetric flask and titrated with 11.10cm3 of 0.300 mol dm-3 sodium hydroxide solution. Determine the percentage purity by mass of the calcium carbonate sample.CaCO3 + HCl -> CaCl2 + H2O + CO2 HCl + NaOH -> NaCl +H2O a. Determine how many moles of hydrochloric acid were used.b. Determine how many moles of excess HCI was titratedc. Determine how much in moles calcium carbonate present in the sample.d. Calculate the mass of calcium carbonate presente. Determine the percentwge calcium carbonate is in the sample.
An analyst weighed 0.25045 g of the Buffalo River Sediment reference material.(RM # 8704) to determine Pb levels. The material was digested in an acid medium toBring it to a solution which was made up to the 30.2450 mL mark with distilled water. If thePb concentration in the control certificate of analysis is (150 ± 17) mg / kg, and theanalyst recovered 95%, what was the concentration of Pb in the solution?
What is the percentage purity of a sample of impure oxalic acid dihydrate if a sample weighing 0.2003 gram requires 29.30 mL of permanganate solution, of which 1.000 mL ≈ 0.006023 g iron?
A stock solution of 0.225 +/- 0.003 M NaNO2 was transferred to a 100 mL volumetric flask (class A) and diluted to the mark. If 7 mL of the stock solution was transferred using one 5-mL and two 1-mL volumetric pipettes, what is the new concentration of the solution and the uncertainty? Please show how to calculate the uncertainty, that is the one part I don't understand how to do
You were tasked to prepare 590 ml of 3.00 M HNO3. If you were provided a stock solution of 70.5% (w/w) HNO3 (MW = 63.0 g) with a specific gravity of 1.42, what volume of this solution (in ml) will you be using?
Approximately 10 mL of 6 M hydrochloric acid were initially added to the euiometer. The eudiometer was then filled with deionized water and placed into a 400-mL beaker contaning ~300 mL of deionized water. Assuming the total volume of solution was 350 mL, and that the solution was uniformly mixed, what was the dilute concentration of the hydrochloric acid?
A sample containing chlorophenol, C6H4ClOH, was analysed by gravimetric analysis. A 0.783-g of this sample goes through a chemical process allowing the chlorine in the chlorophenol to precipitate as silver chloride, weighing 0.271 g. Calculate the % (wt/wt) of the chlorophenol in the sample, assuming that chlorophenol is the only source of chlorine in the sample. Provide your answer to two decimal places and without units. Avoid using scientific notation.
Analytical chemistry is a particular field within the broader spectrum of the chemical sciences, in which many times the focus of analytical experiments is to develop new methods to analyze compounds, either structurally or by determining concentrations of compounds. One of the processes analytical chemists use to determine the exact concentration of a working solution is called standardization. In your own words, describe the differences between a primary, secondary, and tertiary standard, and describe the underlying concept behind the standardization process. Why is it done?
Consider the titration illustrated in Figure 8.] Anhydrous sodium carbonate (Na₂CO₃) is a primary standard. When 0.364 grams of the substance is placed in a conical flask, then 20.00 cm³ of sulphuric acid (H₂SO₄) solution is required to reach the end point of the titration. What is the concentration in mol·dm⁻³ of the sulphuric acid solution? [Give the answer to 3 decimal places. Do not type in the unit. Use a decimal point.] *
An analyst was assigned to work a sample with minerals. This iron-containing sample was analyzed by dissolving a 1.3142g sample in concentrated HCl. The resulting solution was diluted with water and iron (III) was precipitated as the hydrated oxide Fe2O3 xH2O by the addition of HN3. After filtration and washing, the residue was calcined at high temperature to produce 0.5488g of pure Fe2O3 (159.69g / mol). Determine the following:a) the% Fe (55.847 g / mol) and the% Fe3O4 (231.54 g / mol) in the sample.
A pipet is used to transfer 3.00 mL of a 2.00 M stock solution in flask “S” to a 25.00-mL volumetric flask “A,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 3.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”