1. A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by a fish. Having its temperature constant while it travels from the depth of release to water surface, solve for the following: a. kPabs when released b. bubble diameter at 60m depth c. bubble diameter at the water surface h2-60m k. h,-120m SG=1.03

1. A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by a fish. Having its temperature constant while it travels from the depth of release to water surface, solve for the following: a. kPabs when released b. bubble diameter at 60m depth c. bubble diameter at the water surface h2-60m k. h,-120m SG=1.03

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A two-dimensional Rankine half-body, 8 cm thick, isplaced in a water tunnel at 20°C. The water pressure farupstream along the body centerline is 105 kPa. What isthe nose radius of the half-body? At what tunnel flowvelocity will cavitation bubbles begin to form on the surfaceof the body?
A vertical concentric annulus, with outer radius r o and innerradius r i , is lowered into a fl uid of surface tension Y andcontact angle θ < 90 ° . Derive an expression for the capillaryrise h in the annular gap if the gap is very narrow.
Derive an expression for the capillary height change h for afluid of surface tension Y and contact angle θ between twovertical parallel plates a distance W apart, as in Fig. What will h be for water at 20°C if W = 0.5 mm?
A uniform block of steel (SG= 7.85) will “fl oat” at amercury–water interface as in Fig. What is theratio of the distances a and b for this condition?
Venice, Italy, is slowly sinking, so now, especially inwinter, plazas and walkways are fl ooded during storms.The proposed solution is the fl oating levee of Fig. .When fi lled with air, it rises to block off the sea. The leveeis 30 m high, 5 m wide, and 20 m deep. Assume a uniformdensity of 300 kg/m 3 when fl oating. For the 1-m sea–lagoon difference shown, estimate the angle at which thelevee fl oats.
Torricelli problem. A tank whose shape is obtained by rotating y = x6. At t = 0, the water height is y = 2. The hole at the bottom is of area a = 0.05m2. The gravity acceleration is g = 9.8m/s2. How long will it take for all the water to drain from the tank?
A fi sh tank 14 in deep by 16 by 27 in is to be carried in acar that may experience accelerations as high as 6 m/s 2 .What is the maximum water depth that will avoid spillingin rigid-body motion? What is the proper alignment of thetank with respect to the car motion?
The 45 ° V-tube in Fig. contains water and is open atA and closed at C . What uniform rotation rate in r/minabout axis AB will cause the pressure to be equal at pointsB and C ? For this condition, at what point in leg BC will thepressure be a minimum?
Make an analysis of the shape h ( x ) of the water–air interfacenear a plane wall, as in Fig. , assuming that theslope is small, R - 1 ≈ d 2 η / dx 2 . Also assume that the pressuredifference across the interface is balanced by thespecifi c weight and the interface height, ∆p ≈ ρ g η . Theboundary conditions are a wetting contact angle θ at x = 0and a horizontal surface η = 0 as x--->∞. What is themaximum height h at the wall?
An oil drop has a density (?1) of (560+R) kg/m3. The terminal velocity of a spherical drop of thisoil falling in air at the room temperature is (15 + R) cm/s. At the room temperature, air density(?2) is 1.2 kg/m3and its viscosity is 18 μPa.s. Find the radius of the droplet. Consider g =9.81 ??
A pump discharges 8000 liters per minute of a certain brine solution (SG=1.20) to an evaporating pond. The intake line is 25cm in diameter and is at the same level as the pump discharge line, which is 15cm in diameter. The pressure at the inlet of the pump is -170mm of mercury. The pressure gage connected to the pipe discharge reads 150 kPa, and its center is 2.0mabove the center of the discharge flange. The vapor pressure of the brine solution is 40mm of Hg. If the pump efficiency is 80%. How much power is required?
Derive an expression for the capillary- height change h, as shown, for a fluid of surface tension Y and contact angle 0 be- tween two parallel plates W apart. Evaluate for water at 20°C if W = 0.5 mm.