2. A prismatic bar under an axial load produces a tensile stress of 75MPa on a plane at an angle of 0 = 20°, as seen below. Determine the normal and shearing stress on all faces of an element at an angle of e = 50°. 75 MPa 20 deg

2. A prismatic bar under an axial load produces a tensile stress of 75MPa on a plane at an angle of 0 = 20°, as seen below. Determine the normal and shearing stress on all faces of an element at an angle of e = 50°. 75 MPa 20 deg

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.17P: A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at...

See similar textbooks

Related questions

Q: The cylinder for a hydraulic press has an insidediameter of 300 mm and an outside radius of…

A: Pressure is the intensity of force exerted perpendicularly on an area. Shear stress is the intensity…

Q: Two short shafts having identical diameters of 38.0 mm. and rotating at 400 RPM transmitted 26.5 kW…

Q: A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube…

A: a. At inner surface: from the given data, Shear strain,

Q: 41 КРа 4X КРа 27 КРа 2Z kPa D 350 А 8Y KPa 450 88 КРа B E For the state of stress as shown in…

Q: A thin cylinder 75 mm internal diameter, 250 mm long with walls 2.5 mm thick is subjected to an…

A: Stress is defined as the intensity of force acting over a unit area, and strain is the ratio of…

Q: A solid steel post having a length of 3m and a diameter of 80 mm is subjected to pure torsion. a)…

A: Answer: (a) The torsional rigidity of the steel post is 321.7 × 109 N•mm2. (b) The torsional…

Q: 200 kN PROBLEM 8.45 22 mm S kN 60 mm Three forces are applied to the bar shown. Determine the normal…

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: If the principal stresses in a plane stress problem are ơ1 = 100 MPa, ơ2 = 40 MPa, the magnitude of…

A: Write the given values along with suitable variables.

Q: Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected…

A: Acting torque on the system = 200 ×0.15 =30 Nm Bending moment at end section = 200 ×0.25 = 50 Nm the…

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A: Given data: The diameter of the part AB is dAB=15 mm The diameter of the part BC is dBC=18 mm The…

Q: 2. A plane element in a body is subjected to a compressive stress of 80 MPa accompanied by a shear…

Q: Q2. A mild steel shaft of 50 mm diameter is subjected to a bending moment of 1200 N-m and a torque…

Q: Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000…

Q: A body is subjected to a direct tensile stress of 300 MPa in one plane accompanied by a simple shear…

A: given data tensile stress = 300 MPa simple shear = 200 MPa to determine maximum shear stress

Q: wood grains on the board shown below form an angle of 20° with the horizontal. using the circle of…

A: Given data,axial load=250N

Q: According to the maximum strain energy hypothesis, what should be the length L2 in order for the…

A: Given dataTransverse load F1 = 18kNAxial load F2 = 20kNLarger diameter D = 58mmSmaller diameter d =…

Q: Draw Mohr's circle that describes each of the following states of stress shown in Figure 5. 3 ksi 6…

A: given state of stress for element shown in figure a = -12 ksi = - 3 ksi = 0 state of…

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: A spring was made by a steel wire of 25 mm diameter around a 175 mm diameter cylinder. determine the…

Q: 40 60 A circle of 200 mm dia. is drawn on a mild steel plate before it is subjected to two mutually…

A: Given, d = Diameter of the circle = 200 mm σx= Normal stress in horizontal direction = 160 MPa σy=…

Q: 5. The normal and shear stresses acting on one plane passing through a point in a soil mass are 120…

Q: An axial tensile load of 10kN is applied to a 12mm diameter bar. Determine the maximum shearing…

Q: The internal loadings at a cross section through the 130-mm-diameter drive shaft of a turbine…

Q: 8. Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

Q: A certain specimen is subjected to the following stresses: Normal stress along x-axis is 30 kPa,…

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 411 lbs…

Q: The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the…

Q: The principal strains in a plane, measured experimentally at a point on the aluminum fuselage of a…

A: Write down the given value using suitable variables. Here ε1 and ε2 signify principal plane…

Q: · Three forces are applied to the structure shown in Figure 3. Determine the maximum possible normal…

A: Given: Fy=-0.5 kNFx=-3 kNFz=-2.5 kN

Q: 4. For an element subjected to stresses of x= 70 ksi y=-15 ksi xy=30 ksi SAH: (a) Draw Mohr's…

Q: subjected to a shearing force of 715N on its top cylindrical face. If the dowel has a diameter of…

Q: Figure 1. The boiler has an inside diameter of 1800 mm and a wall thickness of 20 mm, and it is made…

Q: 12. A single strain gage is cemented to solid 96-mm-diameter aluminum shaft at an angle B = 20° with…

Q: The state of plane-stress at a point is given by σx = -200 MPa, σy = 100 MPa and txy = 100 MPa The…

A: Data given- σx = -200 MPa, σy = 100 MPa txy = 100 MPa

Q: 2) A shaft of a diameter of 30 mm is transmitting 14,9 kW at 400 rpm. The shaft is connected to a…

A: First of all, make the FBD of the diagram as shown below,

Q: 1.7C1 A. 1.4C1 B CI 0.9C1 Uniform plastic elongation Necking 4Riastic 4% 15% 35% Strain in %…

Q: Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was…

Q: Derive the following equation for computing shear stress in a solid bar along an oblique plane with…

Q: 1. If o, = 20 ksi, o, = 10 ksi, and txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Calculated absolute maximum shear stress.

Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…

Q: t (0) is 0.15°/

A: given:γmax=500×10-6 rad

Q: Two steel springs arranged as shown support a load P. The left spring consists of 12 turns of 20-mm…

Q: 1. A flange coupling connects two shafts to transmit 40 kW at 900 rpm. The flanges of the coupling…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: as per guideline i have to solve only first question

Q: Compare the torsional rigidities of the following sections: (a) a hollow tube 30 mm outside…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

A: Punching is a process is used to make holes in the sheet metal by forcing a tool which is called a…

Question

2. A prismatic bar under an axial load produces a tensile stress of 75MPA on a plane at an angle of 0 =
20°, as seen below. Determine the normal and shearing stress on all faces of an element at an angle of
e = 50°.
75 MPa
20 deg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
At a point on the surface of an elliptical exercise machine, the material is in biaxial stress with t = 1400 psi and trv = —900 psi, as shown in the figure part a. The figure part b shows an inclined plane aa cut through the same point in the material but oriented at an angle ft Determine the value of the angle 6 between zero and 90° such that no normal stress acts on plane aa. Sketch a stress clement having plane aa as one of its sides and show all stresses acting on the clement
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?