A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and the inner d , is 4.5 n and the steel has a value of 11000 ksi For a torque T = 150 K-in determine a) The maximum torsional shear stress in the furthest fiber b) The torsional shear stress in the internal part of the tube c) The angle of rotation per length that is produced to the tube

A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and the inner d , is 4.5 n and the steel has a value of 11000 ksi For a torque T = 150 K-in determine a) The maximum torsional shear stress in the furthest fiber b) The torsional shear stress in the internal part of the tube c) The angle of rotation per length that is produced to the tube

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

A hollow circular pole 3 m high is fixed at the base. It is 6mm thick and its outside diameter is 300mm. The pole is subjected to a torque and a lateral force at the free end. Given: Torque, T = 25 kN-m Lateral Force, N = 3 kN Shear Modulus of Elasticity = 78 GPa Allowable Shear Stress = 60 MPa 1. What is the maximum shear stress (MPa) at the outside surface of the pole due to the torque, T? 2. What is the angle of twist (degree) due to the torque? 3. Find the maximum flexural stress (MPa) at the base of the pole due to the lateral force.
An aluminum tube with the cross section shown has a constant wall thickness of 2 mm. A torque T = 400 N·m is applied to the tube. Use G= 28 GPa What is the area of the tube? a. 957.08mm2 b. 968.09mm2 c. 966.08mm2 d. 977.08mm2 What is the total length of the median line? a. 0.1313m b. 0.1314m c. 0.1315m d. 0.1316m What will be the result shear flow of the object? a. 207,967.94 N/m b. 208,968.98 N/m c. 209,978.96 N/m d. 209,979.00 N/m The shearing stress value will be? a. 104.5 MPa b. 105.6 MPa c. 104.6 MPa d. 105.7 MPa The angle of twist result is? a. 14.68 Deg/m b. 12.66 Deg/m c. 14.68 Deg/m d. None of the above.
Please answer the problem completely. Show a free body diagram. Final answer: Shear stress = 3.2 mpa
1. A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the maximum shear stress in MPa. I need the answer asap pls
If the shear modulus of a material is 120GPa & the bulk modulus is 140 GPa, then Young’s modulus is------ a. 820 GPa b. 280 Pa c. 280 GPa d. 820 Pa
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Q2. A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa.
a) i) The numerical value of plastic section modulus of the solid rectangular section is mm^3 ii) The numerical value of plastic moment of the solid rectangular section is N.mm b) The numerical value of ?t can be calculated as mm
A state of stress at a point A is given by σx = 77 MPa, σy = 3.1 MPa, and τxy = 12 MPa. What is the maximum in-plane shear stress for the point A? Lütfen birini seçin: a. 70.7106 MPa b. 38.8497 MPa c. 83.0846 MPa d. 39.4498 MPa e. None
1. State three underlying assumptions in the formulation of the torsion formula, .TG Jrl == 2 Determine the torsional rigidity of a 300 mm long steel shaft with a diameter of 50 mm. (G = 80 GPa). 3. A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. The maximum allowable shear stress is 50 MPa and the maximum torque to be transmitted by the shaft is 30 % greater than the mean torque. The internal diameter of the shaft is 50 % that of the external diameter. Calculate the shaft dimensions and the angle of twist of the shaft over 3 m when transmitting the above torque (G = 80 GPa).
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?