1. Calculate the torque about the z-axis pointing out of the page at the origin in the following figure given that F₁ = 2 N, F₂=9N, F3 = 4 N, F₁=5 N. Hint: Use the sign convention for torques, counter-clockwise rotation corresponds to a torque in the positive z-direction and clockwise rotation corresponds to a torque in the negative z-direction. Which forces produce clockwise rotations and which forces produce counter-clockwise rotations? While using the formula for cross-product AXB=ABsine, remember that is the angle between the tails of the vectors A and B. To determine e rearrange the vectors so that their tails coincide. Nm k net = tu~ 2 m 3 m K O 2 m F3 FA F₂ YA 30° 20° ILL X

1. Calculate the torque about the z-axis pointing out of the page at the origin in the following figure given that F₁ = 2 N, F₂=9N, F3 = 4 N, F₁=5 N. Hint: Use the sign convention for torques, counter-clockwise rotation corresponds to a torque in the positive z-direction and clockwise rotation corresponds to a torque in the negative z-direction. Which forces produce clockwise rotations and which forces produce counter-clockwise rotations? While using the formula for cross-product AXB=ABsine, remember that is the angle between the tails of the vectors A and B. To determine e rearrange the vectors so that their tails coincide. Nm k net = tu~ 2 m 3 m K O 2 m F3 FA F₂ YA 30° 20° ILL X

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 12.4OQ: Two forces are acting on an object. Which of the following statements is correct? (a) The object is...

See similar textbooks

Similar questions

What is- the magnitude of the angular acceleration of a 25.0-kg disk of radius 0.800 m when a torque of magnitude 10.0 N m is applied to it? (See Section 8.5.)
A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 5.0 angle with the vertical. (b) Does the torque increase or decrease as the angle increases? Explain. Figure P8.6
An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
(a) Give an example in which the net force acting on an object is zero, yet the net torque is nonzero, (b) Give an example in which the net torque acting on an object is zero, yet the net force is nonzero.
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
What three factors affect the torque created by a force relative to a specific pivot point?
Consider the 12.0 kg motorcycle wheel shown in Figure 10.38. Assume it to be approximately an annular ring with an inner radius of 0.280 m and an outer radius of 0.330 m. The motorcycle is on its center stand, so that the wheel can spin freely. (a) If the drive chain exerts a force of 2200 N at a radius of 5.00 cm, what is the angular acceleration of the wheel? (b) What is the tangential acceleration of a point on the outer edge of the tire? (c) How long, starting from rest, does it take to reach an angular velocity of 80.0 rad/s? Figure 10.38 A motorcycle wheel has a moment of inertia approximately
A constant net torque is applied to an object. Which one of the following will not be constant? (a) angular acceleration, (b) angular velocity, (c) moment of inertia, or (d) center of gravity.
Suppose two long straight wires run perpendicular to one another without touching. Does one exert a net force on the other? If so, what is its direction? Does one exert a net torque on the other? If so, what is its direction? Justify your responses by using the right hand rules.
Two forces F1 and F2 act along the two sides of an equilateral triangle as shown in Figure P11.5. Point O is the intersection of the altitudes of the triangle. (a) Find the magnitude of a third force F3 to be applied at B and along BC that will make the total torque zero about the point O. (b) What If? Will the total torque change if F3 is applied not at B but at any other point along BC? Figure P11.5
A grinding wheel is in the form of a uniform solid disk of radius 7.00 cm and mass 2.00 kg. It starts from rest and accelerates uniformly under the action of the constant torque of 0.600 N m that the motor exerts on the wheel. (a) How long does the wheel take to reach its final operating speed of 1 200 rev/min? (b) Through how many revolutions does it turn while accelerating?
Two forces are acting on an object. Which of the following statements is correct? (a) The object is in equilibrium if the forces are equal in magnitude and opposite in direction. (b) The object is in equilibrium if the net torque on the object is zero. (c) The object is in equilibrium if the forces act at the same point on the object. (d) The object is in equilibrium if the net force and the net torque on the object are both zero. (e) The object cannot be in equilibrium because more than one force acts on it.