1. Design 8086’s memory system consisting of 64K bytes of ROM using 32KX8 chip. The memory is to reside over the address range 60000H through 6FFFFH. Select suitable address maps. 2. If the memory chip size is 1024 X 4 bits, how many chips are required to makeup 2K bytes of memory? 3. Interface 16 K word of memory to the 8086-microprocessor system. Available memory chips are 8 K X 8 RAM. Draw the memory table.

1. Design 8086’s memory system consisting of 64K bytes of ROM using 32KX8 chip. The memory is to reside over the address range 60000H through 6FFFFH. Select suitable address maps. 2. If the memory chip size is 1024 X 4 bits, how many chips are required to makeup 2K bytes of memory? 3. Interface 16 K word of memory to the 8086-microprocessor system. Available memory chips are 8 K X 8 RAM. Draw the memory table.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.
What is the starting and ending address of a 256K x 8 memory? How many address lines will be required to interface this memory with 8086? Also, draw the interfacing diagram with 8086
Microprocessors; Draw the figure for flag-bits allocation in an 8086 microprocessor. Explain shortly the meanings of letters used for each flag statues in Assembler.
Eight memory chips of 32*4 bit size have their address buses connected together. What is the size of the memory system ?
1. Draw the programming model of 8086 Microprocessor Note: Please do not handwritten.
Write an assembly language program for 8085 microprocessor to add 2 digit BCD numbers stored in memory location C050H and C051H respectively and store the result in memory location C052H.
Construct a bus system using tri state buffer for 2 registers having 4 bits each.
Consider two microprocessors having 8-bit and 16-bit wide external data buses, respectfully. The two processors are identical otherwise and their bus cycles are the same speed. Suppose all instructions and operands are two Bytes. By what factor do the maximum data transfer rates vary? Suppose all instructions and operands are one Byte. By what factor do the maximum data transfer rates vary? Discuss your answers.
Assume SS=5000H, DS=6000H, ES=7000H, CS=9000H, BX=1000H, DI=2000H, BP=3000H, IP=4000H, SI=2000H, the physical address and the addressing mode of the following memory location specified in the instruction MOV [DI+3000H], AL are ……… and ……… .
Given a 8-bit number at memory location 2050H. Write 8085 instruction to move the value stored at the following locations: Register B Accumulator 2052H Write a single program and show register and accumulator screenshot and also attach memory view. In sim8085 software.
Write an assembly language program in microprocessor 8085 so that I can fetch 2 8 bit numbers from memory locations and store the product, whether it's 8 bit or 16 bit, in 2 different memory locations. I am aware with programming logic. So, only give me the working program and attach a snapshot of the output. No need to explain.
A high-performance microprocessor design requires 1 billion logic gates and is placed in a package that can dissipate 100 W. (a) What is the average power that can be dissipated by each logic gate onthe chip? (b) If a supply voltage of 1.8 V is used,how much current can be used by each gate? Assume a 25 percent duty cycle. (c) What is the totalcurrent required by the IC chip?